Fermentation

Brew Cooler XL 30L Fermenter Bag - for fermenter or kegs

Brew Cooler XL 30L Fermenter Bag - for fermenter or kegs

The Brew Cooler XL is an extra large waterproof, insulated cooling bag to keep correct fermentation temperature in fermenters and kegs up to 30L. Either one 30L fermenter or two cornelius kegs fits inside. Perfect if you dont have space or possibility to place your fermenter in a temperature controlled refrigerator at home.How the Brew Cooler XL worksThe function is simple, place your fermenter or keg(s) inside the Brew Cooler and add frozen water bottles (preferrably plastic) inside the Brew Cooler to reduce and keep the correct fermentation temperature. The volume of frozen water in the plastic bottles determines how many degrees below room temperature the fermenter will be kept at. The frozen water bottles should preferrably be replaced every 24 hours, or when needed.1. Place the Brew Cooler at a suitable location in your home. Place your fermenter with wort inside the Brew Cooler.2. Place the correct number of frozen water bottles inside the Brew Cooler according to the Temperature Chart below.3. Close Brew Cooler zip locks.4. After 24 hours, exchange the frozen water bottles for new ones.Temperature Chart: Choose the correct fermentation temperatureThis chart gives examples of the number and size of frozen water bottles that is needed for a given temperature reduction in the Brew Cooler for 20L beer.One 1-liter bottle reduce 1,5°C.Two 1-liter bottles reduce 3°C.One 1,5-liter bottle reduce 2°C.Two 1,5-liter bottles reduce 4°C.Three 1,5-liter bottles reduce 6°CFour 1,5-liter bottles reduce 8°C.One 2-liter bottle reduce 3°C.Two 2-liter bottles reduce 6°C.Three 2-liters bottles reduce 9°C.Four 2-liter bottles reduce 12°C.These temperature reductions are valid for 20L beer in the fermenter. As can be seen, the temperature reduction is about 1,5°C per liter frozen water. The maximum temperature reduction that can be archieved is about 15°C.Example: If your home ambient temperature is 21°C and you want to ferment 20L ale at 18°C, add one 2-liter or two 1L) frozen plastic water bottle together with your fermenter in the Brew Cooler. Exchange every 24 hours and repeat at least the first 3-4 days during the primary fermentation. If your brew 10L then about half the volume, 1-1.5L frozen water, is enough. What is the correct fermentation temperature?To get your home brew to taste as good as possible its important to control the fermentation temperature. An ale can theoretically be fermented at room temperature, 20-22°C, however it will taste the cleanest when fermented around 18°C, at least the first 3-4 days of fermentation. Lagers should be fermented at 10-12°C. Saisons can be fermented at high temperatures, 20-35°C, depending on the flavour profile you want.Brew Cooler XL 30L specificationsHeight: 70 cmLength 40 cmWidth: 40 cmInternal supports: 60cm Vertical rib supports keeps the bag upright by itself.Material: Tough black polyester with insulation and a grey water proof inner liner.Carrying strap: The Brew Cooler is equipped with an adjustable carrying strap.Note: Fermenters, kegs or other accessories are not included.

€38
Volume discount! €28 per piece when you buy 2 or more
Brewly 30L Conical Fermenter

Brewly 30L Conical Fermenter

Ferment your beer in stainless conical fermeters just like in professional breweries. Rotary racking arm with dip tube provides very good extraction of beer from above the cone. Perfect for batch sizes up to 30L, optimally 20-25L.Brewly 30L Conical Fermenter- Material: Polished stainless steel (ANSI 304)- Polished seamless inside for maximum sanitary conditions- 30L capacity (32L to edge)- Thermometer 0-40C (32-104C) with internal thermowell for the sensor.- Mini valve 3/8" with rotary racking arm with dip tube provides very good extraction of beer from above the cone for bottling or transfer to keg.- Dump valve on conical bottom with 1/2" stainless steel valve, perfect for yeast dumping and easy cleaning.- Internal volume scale up to 30L- 2 steady stainless steel handles- 3 adjustable legs with rubber feet- Airlock with rubber plug- Stainless lid with lock med heavy-duty silicone seal- Diameter: 33,5cm- Height without airlock: 59 cm, adjustable up to 66cm- Height with airlock: 69 cm, adjustable up to76cm- Multiple fermenters can be stacked on top of eachother- Instructions manual in English

€141 €206
DEAL
Temporarily out of stock
View product
Brewly 30L Conical Cooling Fermenter with Chiller

Brewly 30L Conical Cooling Fermenter with Chiller

Ferment your beer in stainless conical fermeters just like in professional breweries. Built-in stainless cooling spiral chiller with gardena-type connectors for easy connections to a cooling medium of your choice. Build-in thermowell for external temperature sensor probe, for example from a thermostat controlling a pump. Rotary racking arm with dip tube provides very good extraction of beer from above the cone. Perfect for batch sizes up to 30L, optimally 20-25L.Brewly 30L Conical Cooling Fermenter with Chiller- Material: Polished stainless steel (ANSI 304)- Polished seamless inside for maximum sanitary conditions- 30L capacity (32L to edge)- 4,7m built-in stainless cooling spiral chiller with gardena-type connectors for easy connections to a cooling medium of your choice.- 30cm stainless thermowell for external temperature sensor probe, for example from a thermostat controlling a pump (like Brewly AC-211/TC-320 universal thermostats).- Thermometer 0-40C (32-104C) with internal thermowell for the sensor.- Mini valve 3/8" provides very good extraction of beer from above the cone for bottling or transfer to keg.- Dump valve on conical bottom with 1/2" stainless steel valve, perfect for yeast dumping and easy cleaning.- Internal volume scale up to 30L- 2 steady stainless steel handles- 3 adjustable legs with rubber feet- Airlock with rubber plug- Stainless lid with lock med heavy-duty silicone seal- Diameter: 33,5cm- Height without airlock: 59 cm, adjustable up to 66cm- Height with airlock: 69 cm, adjustable up to76cm- Multiple fermenters can be stacked on top of eachother- Instructions manual in English

€178 €234
DEAL
Temporarily out of stock
View product
Brewly 60L Conical Fermenter

Brewly 60L Conical Fermenter

Ferment your beer in stainless conical fermeters just like in professional breweries. Rotary racking arm with dip tube provides very good extraction of beer from above the cone. Perfect for batch sizes up to 60L, optimally 20-55L.Brewly 60L Conical Fermenter- Material: Polished stainless steel (ANSI 304)- Polished seamless inside for maximum sanitary conditions- 60L capacity (62L to edge)- Thermometer 0-40C (32-104C) with internal thermowell for the sensor.- Mini valve 3/8" with rotary racking arm with dip tube provides very good extraction of beer from above the cone for bottling or transfer to keg.- Dump valve on conical bottom with 3/4" stainless steel valve, perfect for yeast dumping and easy cleaning.- 2 steady stainless steel handles- 3 legs with rubber feet- Airlock with rubber plug- Stainless lid with lock med heavy-duty silicone seal- Diameter: 47 cm- Height: 70 cm- Multiple fermenters can be stacked on top of eachother- Instructions manual in English

€243 €281
DEAL
Volume discount! €225 per piece when you buy 2 or more
Temporarily out of stock
View product
Brewly 60L Conical Cooling Fermenter with Chiller

Brewly 60L Conical Cooling Fermenter with Chiller

Ferment your beer in stainless conical fermeters just like in professional breweries. Built-in 13-meter stainless cooling spiral chiller with gardena-type connectors for easy connections to a cooling medium of your choice. Build-in thermowell for external temperature sensor probe, for example from a thermostat controlling a pump. Rotary racking arm with dip tube provides very good extraction of beer from above the cone. Perfect for batch sizes up to 60L, optimally 25-55L.Brewly 60L Conical Cooling Fermenter with Chiller- Material: Polished stainless steel (ANSI 304)- Polished seamless inside for maximum sanitary conditions- 60L capacity (62L to edge)- 13-meter built-in stainless cooling spiral chiller with gardena-type connectors for easy connections to a cooling medium of your choice.- 30cm stainless thermowell for external temperature sensor probe, for example from a thermostat controlling a pump (like Brewly AC-211/TC-320 universal thermostats).- Thermometer 0-40C (32-104C) with internal thermowell for the sensor.- Mini valve 3/8" with rotary racking arm with dip tube provides very good extraction of beer from above the cone for bottling or transfer to keg.- Dump valve on conical bottom with 3/4" stainless steel valve, perfect for yeast dumping and easy cleaning.- 2 steady stainless steel handles- 3 legs with rubber feet- Airlock with rubber plug- Stainless lid with lock med heavy-duty silicone seal- Diameter: 47 cm- Height: 70 cm- Multiple fermenters can be stacked on top of eachother- Instructions manual in English

€290 €327
DEAL
Volume discount! €271 per piece when you buy 2 or more
Temporarily out of stock
View product
Brewly 30L Conical Insulation Jacket

Brewly 30L Conical Insulation Jacket

Insulation jacket for the Brewly 30L Conical Fermenter (both versions). Material: 5 mm neoprene foam.

€28 €38
DEAL
Brewtools F40 Unitank 40L Fermenter

Brewtools F40 Unitank 40L Fermenter

Our Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, we've explored new techniques and solutions. This has resulted in a series of high end fermentation tanks with new features and a lot of possibilities.Key Features:- Our PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation.- Cooling jacket in the vertical walls offers efficient cooling without the hazzle of cleaning a spiral.- Many options for connecting accessories like sensors, heaters, carb. stones and other accessories.- Pressure rated for 2 bar / 30 PSI.- 8" TC port on top for easy access.- 2" TC dump and racking valves.Our Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party.Specifications:- Low height w/o acc.: 83 cm- Max height w/o acc.: 103 cm- Packaging size: 85 (h) x 52 (w) x 52 (d) cm  - Net weight: 38 Kg- Gross weight: 44.6 Kg- Tank diameter (inside): Ø40 cm- Gross volume: 51 liter- Max rec. volume: 40 liter- Min rec. volume: 20 liter- Volume, cone: 12 liter- Material: 1.5mm stainless steel (SS304)- Operating pressure: 1.0 bar / 15 PSI- Max pressure: 2.0 bar / 30 PSIIn the box:- Unitank with adjustable frame- 1 pcs Analog pressure gauge, TC34mm- 2 pcs Butterfly-valve, 2"- 1 pcs Butterfly-valve, 34mm DN20- 1 pcs Blow-off pipe- 1 pcs Racking arm 2"- 1 pcs TC elbow 90°, 2"- 1 pcs Insulation jacket, black neoprene- 1 pcs Sample valve, 34mm- 1 pcs TC Adapter 8"-3"- 1 pcs TC blind cap, 3"- 1 pcs TC blind cap 2"- 2 pcs TC blind cap 1.5"- 3 pcs TC blind cap 34mm- 2 pcs TC gasket 8" lipped- 2 pcs TC gasket 3"- 2 pcs TC gasket 2" 5-pack- 1 pcs TC gasket 1.5" 5-pack- 3 pcs TC gasket 34mm 5-pack (DN20)- 1 pcs Tri Clamp 8"- 1 pcs Tri Clamp 3"- 5 pcs Tri Clamp 2"- 2 pcs Tri Clamp 1.5"- 10 pcs Tri Clamp 34mm- 1 pcs TC tool- 4 pcs M10 steel/rubber feet- 1 pcs TC34mm safety valve (PRV, 2 bar)- Necessary bolts and parts for assemblyRecommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Carb. stone kit with Ball-Lock, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, 2" sight glass etc.For more detailed information and user manual, please visit docs.brewtools.com

€1 859
Brewtools F80 Unitank 80L Fermenter

Brewtools F80 Unitank 80L Fermenter

Our Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, we've explored new techniques and solutions. This has resulted in a series of high end fermentation tanks with new features and a lot of possibilities.Key Features:- Our PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation.- Cooling jacket in the vertical walls offers efficient cooling without the hazzle of cleaning a spiral.- Many options for connecting accessories like sensors, heaters, carb. stones and other accessories.- Pressure rated for 2 bar / 30 PSI.- 8" TC port on top for easy access.- 2" TC dump and racking valves.Our Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party.Specifications:- Low height w/o acc.: 110 cm- Max height w/o acc.: 130 cm- Packaging size: 113 (h) x 52 (w) x 52 (d) cm  - Net weight: 44.8 Kg- Gross weight: 50 Kg- Tank diameter (inside): Ø40 cm- Gross volume: 86 liter- Max rec. volume: 80 liter- Min rec. volume: 20 liter- Volume, cone: 12 liter- Material: 1.5mm stainless steel (SS304)- Operating pressure: 1.0 bar / 15 PSI- Max pressure: 2.0 bar / 30 PSIIn the box:- Unitank with adjustable frame- 1 pcs Analog pressure gauge, TC34mm- 2 pcs Butterfly-valve, 2"- 1 pcs Butterfly-valve, 34mm DN20- 1 pcs Blow-off pipe- 1 pcs Racking arm 2"- 1 pcs TC elbow 90°, 2"- 1 pcs Insulation jacket, black neoprene- 1 pcs Sample valve, 34mm- 1 pcs TC Adapter 8"-3"- 1 pcs TC blind cap, 3"- 1 pcs TC blind cap 2"- 2 pcs TC blind cap 1.5"- 3 pcs TC blind cap 34mm- 2 pcs TC gasket 8" lipped- 2 pcs TC gasket 3"- 2 pcs TC gasket 2" 5-pack- 1 pcs TC gasket 1.5" 5-pack- 3 pcs TC gasket 34mm 5-pack (DN20)- 1 pcs Tri Clamp 8"- 1 pcs Tri Clamp 3"- 5 pcs Tri Clamp 2"- 2 pcs Tri Clamp 1.5"- 10 pcs Tri Clamp 34mm- 1 pcs TC tool- 4 pcs M10 steel/rubber feet- 1 pcs TC34mm safety valve (PRV, 2 bar)- Necessary bolts and parts for assemblyRecommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Carb. stone kit with Ball-Lock, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, 2" sight glass etc.For more detailed information and user manual, please visit docs.brewtools.com

€2 102
Temporarily out of stock - Advance booking available
View product
Mangrove Jack's Heat Pad

Mangrove Jack's Heat Pad

The heat pad ensures constant brewing temperature which is crucial for the success of brewing beer, wine or spirits. To be placed under the fermenter. Suitable for fermentation in cold areas such as in a refrigerator or in the basement, garages or on the balcony. Provides a low constant heat to the fermenter which aids yeast activity and helps avoid stuck fermentations.Use preferrably in cojunction with an Universal Thermostat (not included).Features:- Inexpensive to run. - Voltage: 220-240V EU-version power cord (UK power cord NOT included).- Power: 25W- Width: 32 cm- Length: 32 cm

€38
Fermenter 15L with lid

Fermenter 15L with lid

Fermenter made of food grade plastic. Lid and rubber seal for air lock are included. Graded to 12L, 15L maximum.MeansurementsHeight: 32 cmDiameter: 30 cmNote: Fermenter air lock is not included.

€7,4
Fermenter 15L with lid and tap hole

Fermenter 15L with lid and tap hole

Fermenter 15L with lid and tap hole

€10
Fermenter 15L with lid and tap

Fermenter 15L with lid and tap

Fermenter 15L with lid and tap

€13
Lid for 15L fermenter

Lid for 15L fermenter

Plastic lid for 15L fermenter with rubber bussing.

€1,8
Fermenter 30L with lid

Fermenter 30L with lid

Fermenter made of food grade plastic. Lid and rubber seal for air lock are included. Graded to 25L, 30L maximum.MeansurementsHeight: 44 cmDiameter: 37 cmNote: Fermenter air lock is not included.

€13
Jäskärl 30-liter med lock 3-pack

Jäskärl 30-liter med lock 3-pack

Fermenter made of food grade plastic. Lid and rubber seal for air lock are included. Graded to 25L, 30L maximum.MeansurementsHeight: 44 cmDiameter: 37 cmNote: Fermenter air lock is not included.

€35 €37
DEAL
Fermenter 30L with tap-hole and lid

Fermenter 30L with tap-hole and lid

Fermenter 30L with tap-hole and lid

€14
Jäskärl 30-liter med lock och hål för tappkran 3-pack

Jäskärl 30-liter med lock och hål för tappkran 3-pack

Three Fermenters 30L with tap-hole and lid

€41 €42
DEAL
Fermenter 30L with tap and lid

Fermenter 30L with tap and lid

Fermenter 30L with tap and lidHeight: 44cmDiameter: 37cm

€16
Fermenter 30L with tap and lid 3-pack

Fermenter 30L with tap and lid 3-pack

Three Fermenter buckets 30L with tap and lidHeight: 44cmDiameter: 37cm

€42
Lid for 30L fermenter

Lid for 30L fermenter

Plastic lid for 30L fermenter with rubber bussing.

€2,5
Fermenter air lock

Fermenter air lock

Fermenter air lock

€0,9
Airlock Cylindrical 3-piece

Airlock Cylindrical 3-piece

3-piece airlock in transparent plastic that fits ordinary plastic fermenters as well as FermZilla and Brewly fermenters. Easy to clean. Fits 9mm holes.

€1,8
Volume discount! €1,4 per piece when you buy 2 or more
Fermenter tap with nut

Fermenter tap with nut

Fermenter tap with nipple (9/12mm) with nut and rubber gasket. Fits holes 25-26mm diameter. Recommended silicone hose inner diameter for the nipple is 9-10mm.

€3,3
Rubber Seal for Airlock

Rubber Seal for Airlock

Rubber Seal for Airlock that fits 15L and 30L fermenters.

€0,8
Volume discount! €0,7 per piece when you buy 2 or more
Synthetic Plug for Airlock 18/24mm

Synthetic Plug for Airlock 18/24mm

Synthetic plug for airlock 18/24mm with 9mm hole. Cylindroconical form, 18mm diameter in one end and 24mm in the other.

€2,7
Silicone Plug for Airlock 18/24mm

Silicone Plug for Airlock 18/24mm

Silicone plug for airlock 18/24mm with 9mm hole. Cylindroconical form, 18mm diameter in one end and 24mm in the other.

€1,8
Silicone Plug for Airlock 21/27mm

Silicone Plug for Airlock 21/27mm

Silicone plug for airlock 21/27mm with 9mm hole. Cylindroconical form, 21mm diameter in one end and 27mm in the other.

€2,7
Silicone Plug for Airlock 23/29mm

Silicone Plug for Airlock 23/29mm

Silicone plug for airlock 23/29mm with 9mm hole. Cylindroconical form, 23mm diameter in one end and 29mm in the other.

€3,3
Silicone Plug for Airlock 31/38mm

Silicone Plug for Airlock 31/38mm

Silicone plug for airlock 31/38mm with 9mm hole. Cylindroconical form, 31mm diameter in one end and 31mm in the other.

€5,5
Silicone Plug for Airlock 41/49mm

Silicone Plug for Airlock 41/49mm

Silicone plug for airlock 41/49mm with 9mm hole. Cylindroconical form, 41mm diameter in one end and 49mm in the other.

€8,3
Rubber Stopper Grey 8/12 mm

Rubber Stopper Grey 8/12 mm

Durable rubber stopper for test tubes, pistons M.M.

€0,6
Temporarily out of stock
View product
Rubber Stopper Grey 13/17 mm

Rubber Stopper Grey 13/17 mm

Durable rubber stopper for test tubes, pistons M.M.

€0,7
Rubber Stopper Grey 19/26 mm

Rubber Stopper Grey 19/26 mm

Durable rubber stopper for test tubes, pistons M.M.

€1,4
Rubber Stopper Grey 29/38 mm

Rubber Stopper Grey 29/38 mm

Durable rubber stopper for test tubes, pistons M.M.

€1,8
Temporarily out of stock
View product
Hop Filter 29cm

Hop Filter 29cm

Hop filter in stainless steel, perfect for dry hopping beer in Cornelius kegs or fermenters. Loop for hanging it. Length: 29cm. Diameter: 7cm.

€27
Thermometer LCD 2-36 degrees

Thermometer LCD 2-36 degrees

Thermometer LCD 2-36 degrees Celcius. Self-adhesive. Perfect for the fermenter. Size: 21x148 mm.

€1,8
Volume discount! €1,4 per piece when you buy 2 or more
Brewly AC-211 Digital Universal Thermostat

Brewly AC-211 Digital Universal Thermostat

Brewly AC-211 Digital Universal Thermostat. EU-version power cord (UK power cord not included). Can control one Heating source and one Cooling source. Sensor included.

€38
Temporarily out of stock
View product
Brewly TC-320 Digital Universal Thermostat

Brewly TC-320 Digital Universal Thermostat

Brewly TC-320 Digital Universal Thermostat. EU-version power cord (UK power cord not included).

€38
Temporarily out of stock
View product
Inkbird ITC-308 Universal Thermostat

Inkbird ITC-308 Universal Thermostat

Inkbird ITC-308 Digital Temperature Controller Outlet Thermostat with Dual Screen Readouts, w/Sensor. For Home Brewing & Fermentation, Breeding & Incubation, Greenhouse, Kombucha.- Plug and play design, easy to use. - Support reading with Centigrade or Fahrenheit. - Maximum output load: 1100W(110V) / 2200W(220V). - Temperature calibration, Compressor delay protection for refrigeration control.- High and low temperature alarms are available. - Dual relay output, be able to connect with refrigeration and heating equipment at the same time. - Dual display window, be able to display measured temperature and set temperature at the same time. - Heating/Cooling differential function could be set separately for refrigeration and heating to protect temperature controller from violent change.Specifications- Temperature Control Mode :On/Off Control, Heating and Cooling - Temperature Control Range : -40~100 °C / -40~212 ° F - Temperature Resolution: 0.1 ° C / 0.1° F ​- Temperature Accuracy: ±1°C (-50 ~ 70°C) / ±1°F (-50 ~ 160° F) - Ambient Temperature: -30~ 75 ° C / -22~ 167 ° F- Input Power: 100 ~240VAC, 50Hz/60Hz - Temperature Control Output: Max. 10A, 100V ~240V AC - Input Power Cable Length: 1.5m (5ft) ​- Output Power Cable Length: 30cm (1ft)- Sensor Type: NTC sensor (Including) - Sensor Length: 2m / 6.56ft ​- Sensor's probe dimension: 50mm x 6mm- Dimension Body: 140x68x33mm (5.5x2.7x1.3inch)- Socket (EU Version): 135x54x40mm (5.3x2.1x1.6 inch)

€52
Inkbird ITC-310T-B Universal Thermostat

Inkbird ITC-310T-B Universal Thermostat

INKBIRD ITC-310T-B is a dual relay thermostat which can be set to automatically control 12 individual temperatures for 12 time slots. It is widely used for homebrew, aquarium, pet breeding, hatching, fermentation, seed sprouting and etc.12 individual temperatures for 12 time slots: INKBIRD ITC-310T-B can be set 12 individual temperatures for 12 time slots. Once the practical temperature reaches its set temperature, its timer will be started automatically, which will be much better and more precise for the monitored creatures and/or plants.Wide application contexts: INKBIRD ITC-310T-B is widely used for homebrew, aquarium, pet breeding, hatching, barbecue, boiler temperature control, geothermal temperature control, heating pump constant temperature cycle, strain culture fermentation, seed sprouting, electric heating, electric oven, over-temperature protection and automatic temperature control system of all kinds of electrical equipment and etc.Flexible control mode: it supports single mode and cycle control mode; we can choose and/or switch the control mode based on our practical needs.Specifications INKBIRD ITC-310T-BTemperature Control Range: -50~120°C/-58~248°FTemperature Resolution: 0.1°C / 0.1°FMeasuring Accuracy: ±1°C (-50 ~ 70°C) / ±1°F(-58 ~ 158°F)Temperature Control Mode: On/Off Control, Heating and CoolingTiming Accuracy: 24 hours±1.7sTiming Range: 1~999 (min/hour/day)Periods of Time Max: 12 periodsCycle Setting: 1-999 times cycle, or 00 infinite cycleInput Voltage: 100 ~240VAC, 50Hz/60HzControl Output Current: Max.10AVoltage: 100~240V ACPower: Max.1200W(120V)/2200W(220V)Alarm: High and Low Temperature AlarmSensor Type: NTC Sensor(including)Sensor Length: 2m / 6.56ftRelay Output: Cooling(10A,100-240VAC)Heating(10A,100-240VAC)

€66
Inkbird ITC-308 WiFi Universal Thermostat

Inkbird ITC-308 WiFi Universal Thermostat

Inkbird WiFi ITC-308 Digital Temperature Controller Outlet Thermostat with Dual Screen Readouts, w/Sensor. For Home Brewing & Fermentation, Breeding & Incubation, Greenhouse, Kombucha.- Plug and play design, easy to use. - WIFI smart controller supports both IOS & Android,WIFI supports 2.4GHz Wi-Fi router, free APP “InkbirdSmart” which is able to monitor temperature at any time.- Support reading with Centigrade or Fahrenheit. - Maximum output load: 1100W(110V) / 2200W(220V). - Temperature calibration, Compressor delay protection for refrigeration control.- High and low temperature alarms are available. - Dual relay output, be able to connect with refrigeration and heating equipment at the same time. - Dual display window, be able to display measured temperature and set temperature at the same time. - Heating/Cooling differential function could be set separately for refrigeration and heating to protect temperature controller from violent change.Specifications- Temperature Control Mode :On/Off Control, Heating and Cooling - Temperature Control Range : -40~100 °C / -40~212 ° F - Temperature Resolution: 0.1 ° C / 0.1° F ​- Temperature Accuracy: ±1°C (-50 ~ 70°C) / ±1°F (-50 ~ 160° F) - Ambient Temperature: -30~ 75 ° C / -22~ 167 ° F- Input Power: 100 ~240VAC, 50Hz/60Hz - Temperature Control Output: Max. 10A, 100V ~240V AC - Input Power Cable Length: 1.5m (5ft) ​- Output Power Cable Length: 30cm (1ft)- Sensor Type: NTC sensor (Including) - Sensor Length: 2m / 6.56ft ​- Sensor's probe dimension: 50mm x 6mm- Dimension Body: 140x68x33mm (5.5x2.7x1.3inch)- Socket (EU Version): 135x54x40mm (5.3x2.1x1.6 inch)

€65
Temporarily out of stock
View product
Kegmenter Unitank 29L Fermenter/Keg

Kegmenter Unitank 29L Fermenter/Keg

These 29L stainless steel vessels are designed just like a commercial beer keg but with a large 10cm (4inch) tri-clover opening at the top so you can easily get inside the keg to clean it out. This new 29L Size is perfect for doing 20-25L batches so you have a bit of spare head space inside the Kegmenter.This the stainless steel Kegmenter comes with airlock and flat plate however you can also use this kegmenter under pressure if you want to. If you want to use this Kegmenter under pressure then we would recommend that you purchase the lid with ball lock posts and pressure relief vale.The Kegmenter can hold 2.5bar which makes it possible to carbonate and ferment in the same vessel. You can force carbonate using the Pressure Kit (sold seperately).Being able to hold pressure also means you can push the beer out of the fermenter directly through a filter or even dispense directly from fermenter to draft beer tap if you wanted to.SpecificationsVolume: 29L (7.6 Gallons)Maximum Working Pressure: 2.5 BARTest Pressure: 5 BAR Wall Thickness (Body/Chimes): 1.8mm/2.1mmDiameter: 39,5cmHeight: 38cmDatasheetClick here to open the datasheet

€224
Kegmenter Unitank 58L Fermenter/Keg

Kegmenter Unitank 58L Fermenter/Keg

These 29L stainless steel vessels are designed just like a commercial beer keg but with a large 10cm (4inch) tri-clover opening at the top so you can easily get inside the keg to clean it out. This new 29L Size is perfect for doing 20-25L batches so you have a bit of spare head space inside the Kegmenter.This the stainless steel Kegmenter comes with airlock and flat plate however you can also use this kegmenter under pressure if you want to. If you want to use this Kegmenter under pressure then we would recommend that you purchase the lid with ball lock posts and pressure relief vale.The Kegmenter can hold 2.5bar which makes it possible to carbonate and ferment in the same vessel. You can force carbonate using the Pressure Kit (sold seperately).Being able to hold pressure also means you can push the beer out of the fermenter directly through a filter or even dispense directly from fermenter to draft beer tap if you wanted to.SpecificationsVolume: 29L (7.6 Gallons)Maximum Working Pressure: 2.5 BARTest Pressure: 5 BAR Wall Thickness (Body/Chimes): 1.8mm/2.1mmDiameter: 39,5cmHeight: 38cmMaterial: 304 Stainless steelDatasheetClick here to open the datasheet

€280
Kegmenter Pressure Kit

Kegmenter Pressure Kit

This pressure kit is so you can convert the 29 and 58L Kegmenters into either pressure rated fermenters or use the Kegmenters as ball lock kegs. This lid comes with a red pressure relief valve (that opens at 2.5bar - compatible thread to cornelius type PRVs). The lid has accurately machined gas and liquid posts.This lid is ideally suited to also fermenting under pressure so you can use a spunding valve/adjustable pressure relief valve so you can naturally carbonate during primary fermentation.It should be noted that we now make this lid with a 60cm silicon dip tube with a stainless fload. This innovative design means when you draw liquid from this kegmenter the liquid will always be drawn from the top 2.5cm of liquid meaning only the clearest wort/beer will be drawn from the kegmenter. This is particulrly useful if you are dispending directly from the fermenter or simply want to separate clear liquid from sediment which has sunken to the bottom of the kegmenter.

€66
Mangrove Jack's Stainless Steel Fermenter 25L

Mangrove Jack's Stainless Steel Fermenter 25L

Ferment with stainless steel like the pros! A high quality stainless steel fermenter with seamless inside for easy cleaning to prevent contamination. It has a 25 L capacity with litre measurements stamped on the inside body and handles for easy lifting. This also comes with a bung and bubbler airlock. Mangrove Jack's Stainless Steel Fermenter 25L- 25 L Capacity- Stainless steel tap- High grade, #304, scratch resistent, stainless steel body- Litre measurements stamped on the inside body of fermenter- Height = 520mm (to top of lid)- Height = 620mm (including vintage airlock)- Height = 480mm (to top edge without lid)

€206
Grainfather SF70 Conical Fermenter 70L

Grainfather SF70 Conical Fermenter 70L

The SF70 is our largest and tallest fermenter yet. With a 70L capacity it’s designed to hold big batches of wort after a big brew day. The SF70 can be adapted to suit your brewing space with an adjustable leg height and castor wheels for easy manoeuvrability. Its intuitive design, 304 grade stainless steel build, and 113° angle conical makes both fermentation and cleaning easy. FEATURESSF70 body built out of high grade, 304 stainless steel113° angle conical avoids yeast and sediment getting stuck to the sides of the coneAdjustable leg height and castor wheels for easy manoeuvrabilityEasily dump yeast with a separate valveInsert temperature probes into the built-in thermowell for accurate temperature readingsTransfer and take samples above the yeast and trub line with an accessible valve on the side of the unit Compatible with the GCA for accurate temperature controlWe’re confident that our products will produce professional results, just like the craft breweries. That’s why every SF70 comes with a 2-year warranty.WHAT'S INCLUDED?- Grainfather SF70- Stainless steel lid with 38mm tri-clamp fitting- Rubber bung & airlock- Thermowell (use with GCA or thermometer)- Cone mounted 10mm stainless steel barbed sample valve- 19mm bottom mounted stainless steel dump valve- Adjustable and removeable legs with castor wheelsSize: 1300 x 410mm (including air lock and in highest leg position)Weight: 13kgCapacity: 70LMax fermentation volume: 65LPower: NoneConnectivity: NoneCone angle: 113°

€542
Grainfather Conical Fermenter 30L Pro Edition

Grainfather Conical Fermenter 30L Pro Edition

The Grainfather Conical Fermenter Pro Edition allows you to control the heating of your unit (and cooling with the Glycol Chiller available separately), dump yeast, take samples and transfer your wort via our innovative dual function valve design. Note: EU-version power cord (UK power cord NOT included).Ferment like never before! The Grainfather Conical Fermenter give the brewer professional fermentation control, just like the commercial breweries. Fermentation is arguably the most important part of producing a good quality beer. A good fermentation environment starts with a clean and sterile fermenter, has a consistent controlled temperature base and exposure to oxygen is minimised. The Grainfather Conical Fermenter provides you with a modular system for all of this and more!FEATURESDouble Walled: A stainless steel double walled skin is filled with a thick layer of polyurethane foam for insulation. This is what keeps the wort at a constant stable temperature with minimal influence from any external environmental temperature changes, providing insulation for your fermentation that a standard jacket cannot achieve. Integrated Gentle Heating: In the cavity of the fermenter between the outer body and cone sits a 30 Watt, 12V heating element. Unlike standard heating elements/sources that directly heat the liquid, this heat source is designed to heat the environment in between the walls of the fermenter, which in turn heats the liquid. It is similar to controlling the temperature in a temperature controlled room. The fermenter acts as an artificial environment which can be heated, meaning the temperature is raised in an even and controlled manner which is much better for the yeast. Integrated Cooling Sleeve: In between the two stainless steel walls sits a cooling sleeve (also made of stainless steel). This cooling sleeve is welded onto the inner wall of the fermenter and can be hooked up to the additionally purchased Glycol Chiller. Temperature is dialed into the Temperature Controller and as the cooling liquid travels through this sleeve, it cools the stainless steel which in turn evenly cools the beer in the fermenter. The cooling sleeve never comes into contact with the beer, it is completely concealed, built into the fermenter and never needs cleaning or sanitising - a true innovation for a fermenter of this scale.Easy Access to the Interior for Hassle Free Cleaning: The Grainfather Conical Fermenter has a smooth interior with no additions such as cooling coils or additional sampling valves meaning it is easy to clean and minimises the risk of infection.Golden Angle Conical:The conical shape of the fermenter is typical for professional breweries. Our conical has been designed with the 'Golden Angle' of 60º. This is the optimum angle for yeast and sediment to drop down to the bottom of the cone without getting stuck to the sides, allowing you to transfer from above the sediment line, resulting in clearer beer. The conical shape also allows for better mixing during fermentation due to the path of convention currents that it enables to occur. Dual Valve Tap: Make the yeast dumping, transferring and sampling process more professional with this innovative all in one valve. Sampling and transferring is done through an inlet above the sediment line, allowing for clear, sediment free beer. Easily collect your yeast from below the sediment line with the same unique valve for recultivating and pitching. The innovative design of the valve allows for this dual functionality and less cleaning for you. Temperature Control: The Temperature Controller easily snaps on via magnets and pogo pins. Allowing you to accurately dial in a temperature and even set a temperature schedule/profile (you can set up to 4 profiles each with 5 stages). It can control the heating of the integrated heating element and the cooling (if you have upgrade to the Glycol Chiller). Support: The Grainfather Conical Fermenter is fully supported around the world by a fantastic support team who love brewing just as much as you do. Our support team is here for any technical enquiries on brewing or how the Conical Fermenter works, as well as general customer service enquiries.

 All Grainfather Conical Fermenters come with a 24 month warranty. EU-power plug (UK-plug not included)

€617 €626
DEAL
Grainfather Conical Fermenter 30L Pro Cooling Edition

Grainfather Conical Fermenter 30L Pro Cooling Edition

The Grainfather Conical Fermenter Pro Cooling Edition allows you to control the heating of your unit, dump yeast, take samples and transfer your wort via our innovative dual function valve design. Note: EU-version power cord (UK power cord NOT included).The Cooling Pump Kit allows users of the Grainfather Conical Fermenter to control the fermentation temperature with cold water by pumping it through the double walled insulated interior.Ferment like never before! The Grainfather Conical Fermenter give the brewer professional fermentation control, just like the commercial breweries. Fermentation is arguably the most important part of producing a good quality beer. A good fermentation environment starts with a clean and sterile fermenter, has a consistent controlled temperature base and exposure to oxygen is minimised. The Grainfather Conical Fermenter provides you with a modular system for all of this and more!FEATURES:Double Walled: A stainless steel double walled skin is filled with a thick layer of polyurethane foam for insulation. This is what keeps the wort at a constant stable temperature with minimal influence from any external environmental temperature changes, providing insulation for your fermentation that a standard jacket cannot achieve. Integrated Gentle Heating: In the cavity of the fermenter between the outer body and cone sits a 30 Watt, 12V heating element. Unlike standard heating elements/sources that directly heat the liquid, this heat source is designed to heat the environment in between the walls of the fermenter, which in turn heats the liquid. It is similar to controlling the temperature in a temperature controlled room. The fermenter acts as an artificial environment which can be heated, meaning the temperature is raised in an even and controlled manner which is much better for the yeast. Integrated Cooling Sleeve: In between the two stainless steel walls sits a cooling sleeve (also made of stainless steel). This cooling sleeve is welded onto the inner wall of the fermenter and can be hooked up to the Cooling Pump Kit. Temperature is dialed into the Temperature Controller and as the iced cold water travels through this sleeve, it cools the stainless steel which in turn evenly cools the beer in the fermenter. The cooling sleeve never comes into contact with the beer, it is completely concealed, built into the fermenter and never needs cleaning or sanitising - a true innovation for a fermenter of this scale.Basic Cooling Pump Kit: The Cooling Pump Kit allows users of the Grainfather Conical Fermenter to control the fermentation temperature with cold water by pumping it through the double walled insulated interior.Easy Access to the Interior for Hassle Free Cleaning: The Grainfather Conical Fermenter has a smooth interior with no additions such as cooling coils or additional sampling valves meaning it is easy to clean and minimises the risk of infection.Golden Angle Conical:The conical shape of the fermenter is typical for professional breweries. Our conical has been designed with the 'Golden Angle' of 60º. This is the optimum angle for yeast and sediment to drop down to the bottom of the cone without getting stuck to the sides, allowing you to transfer from above the sediment line, resulting in clearer beer. The conical shape also allows for better mixing during fermentation due to the path of convention currents that it enables to occur. Dual Valve Tap: Make the yeast dumping, transferring and sampling process more professional with this innovative all in one valve. Sampling and transferring is done through an inlet above the sediment line, allowing for clear, sediment free beer. Easily collect your yeast from below the sediment line with the same unique valve for recultivating and pitching. The innovative design of the valve allows for this dual functionality and less cleaning for you. Temperature Control: The Temperature Controller easily snaps on via magnets and pogo pins. Allowing you to accurately dial in a temperature and even set a temperature schedule/profile (you can set up to 4 profiles each with 5 stages). It can control the heating of the integrated heating element and the cooling via the Cool Pump Kit. Support: The Grainfather Conical Fermenter is fully supported around the world by a fantastic support team who love brewing just as much as you do. Our support team is here for any technical enquiries on brewing or how the Conical Fermenter works, as well as general customer service enquiries.

 All Grainfather Conical Fermenters come with a 24 month warranty. EU-power plug (UK-plug not included)

€655 €710
DEAL
Grainfather Conical Fermenter Insulation Jacket

Grainfather Conical Fermenter Insulation Jacket

The GF30 Coat is the perfect fitment for those in a climate that experiences high condensation rates when using either using the GC4 Glycol Chiller or Cooling Pump Kit to lower the fermenter’s temperature. Fits Grainfather Conical Fermenter.Features:Made from high quality 5mm thick SBR foam.Consists of two independent sections for both the main body and the fermenter cone for total coverage.

€34
Grainfather Conical Fermenter Temp Controller

Grainfather Conical Fermenter Temp Controller

The Grainfather Digital Temperature Controller replaces the temperature display. With this you can control the heating and the cooling (if you have the Grainfather Glycol Chiller) of your fermenter by dialing in a temperature or even setting a temperature schedule (can set up to 5 stages). This snaps on easily via magnets and pogo pins with no extra cords or clutter.Control the heating element and Glycol Chiller (available separately)Choose between imperial and metric (C° & F°)Total of 4 fermentation profiles with up to 5 steps each (2 are pre-set for a lager and an ale, 2 are custom)Hysteresis is customisable and able to be set at 0.1 intervals between a range of 0.1°C – 1.9°C & 0.2°F - 2.9°F (the default setting is 0.5°C)

€57 €59
DEAL
Grainfather Conical Fermenter Dual Valve Tap

Grainfather Conical Fermenter Dual Valve Tap

Make the yeast dumping, transferring and sampling process more professional with this innovative all in one valve. Sampling and transferring is done through a valve above the sediment line, allowing for clear, sediment free beer. Collect your yeast from below the sediment line for recultivating and pitching. - Dual Valve Tap with 110 mm (4.3”) liquid inlet

€90 €94
DEAL
Grainfather Pump & Adapter for Conical Fermenter (Pump Kit)

Grainfather Pump & Adapter for Conical Fermenter (Pump Kit)

Grainfather Pump & Adapter for Conical Fermenter (Pump Kit). NOTE! Spare part.

€36
Temporarily out of stock
View product
Grainfather Glycol Chiller

Grainfather Glycol Chiller

New version with touch panel (LED). Control your fermentation temperature accurately, every time! Temperature control is one of the most crucial elements for producing a good quality beer. It needs to be regulated and stable throughout the whole fermentation process to ensure the yeast doesn't get stressed and ferments correctly to get the right flavour profile. With the ability to individually power and control the temperature of up to four Grainfather Conical Fermenters, each with their own fermenting schedules, the Grainfather Glycol Chiller is the perfect addition to ensure superior fermenting results.Design:With a sleek and compact design, that still accommodates our full array of features, the Glycol Chiller maintains the Grainfather’s principle of providing quality home brewing equipment, that deliver’s craft brewery like results, on a small footprint. With the addition of the Glycol Chiller, your system is operating at the ultimate level and you are even able to cold crash and lager down to 4°C (39°F). The Glycol Chiller connects to a hidden cooling sleeve, located in between the two stainless steel walls of the Conical Fermenter. Your desired temperature is dialed into the digital temperature controller on the Conical Fermenter, the liquid then travels through this sleeve, cooling the stainless steel which in turn cools the beer in the fermenter. The cooling sleeve never comes into contact with the beer, is completely concealed and does not need cleaning or sanitising - a true innovation for a fermenter on this scale.Features:- Allows you to cold crash 23 L (6 US Gal) of wort to as low as 4-6ºC (39-43°F). Minimum temperature will vary based on external factors such as ambient room temperature, the number of fermenters connected and other environmental conditions.- Cools and powers up to 4 Conical Fermenters at different temperatures and fermenting schedules.Note: The instructions for the Glycol Chiller will be attached to the outside of the shipping box. It is important that you retain these, do not throw them away and read them carefully before use to ensure no damage occurs to the unit. If these for any reason are not included with your purchase, we highly recommend you download a new copy via the instructions tab on this page and read them carefully.Glycol Chiller includes:- Wall outlet power cord with plug- 2 x cooling connection couplers- 2 x 2 m (6.5 ft) insulated hoses- 1 x Glycol Funnel- 1 x silicon tube for priming pump- 1 x 3 L (3 US qt) propylene glycolNOTE: When you receive your unit, you will need to fill it up with a propylene glycol mixture. Refer to the instructions provided with the Glycol Chiller for mixing, filling and pump priming information.Warranty:There is 24 month warranty for Glycol Chillers. Specifications:- Touch LED display panel- 6 L (1.5 US Gal) glycol tank- 300 W- 220 – 240 V, 50Hz- Noise level (operating): 50-60 dB- EU-version power cord (UK power cord NOT included).- 390W x 450D x 656H (mm)- Weight: 28.3 kg (62 lbs)InstructionsClick here to open the manual

€935
Grainfather Glycol Chiller Adapter Kit

Grainfather Glycol Chiller Adapter Kit

With the Grainfather Glycol Chiller Adapter (GCA), you can easily control the temperature of your fermenter together with the Grainfather Glycol Chiller. Can be used in several models of fermenters and has both cooling and heating to provide a stable fermentation temperature.The kit consists of a cooling coil that is mounted through a rubber bung, which also has room for a airlock or blow-off, down into the fermenter. This coil is then connected to one of the channels on the Clycol Chiller.The control unit is of the same model as in Grainfathers Conical Fermenter Pro and handles the heating element and the glycol cooler's coolant pump to regulate temperature in the fermenter. It also supports Wi-Fi and the Grainfather App, which offers the user the ability to monitor and control the fermentation remotely. The unit's temperature probe is mounted on the outside of the fermenter or in a thermowell.The heating element is 30 W and is mounted with self-adhesive tape on the side of the fermenter.Specifications:Heating element - 12 V, 30 W. Dimension: 22 x 8 cm. Cord 2 mCooling coil - 5 m, 9 mm pipe outer diameter. The coil is 12 cm wide and 52 cm highTemperature probe - 35 x 6 mm. Cord 2 mControl unit - 12V. WiFI support, color display, Power cord 2 m.Cooling connection hoses - Insulation. length 2 meters, inner diameter 8 mm

€197
Propylene Glycol Pure 1L

Propylene Glycol Pure 1L

Propylene Glycol Pure 1L 99,8%. Food grade. Can also be used with Grainfather Glycol Chiller for example. Volume 1L.

€17
Grainfather Propylene Glycol 3L

Grainfather Propylene Glycol 3L

Original Propylene Glycol for Grainfather Glycol Chiller for example. Volume 3L.

€38
Grainfather Cooling Pump Kit

Grainfather Cooling Pump Kit

Temperature control is one of the most crucial elements for producing a good quality beer. It needs to be regulated and stable throughout the whole fermentation process to ensure the yeast doesn't get stressed and ferments correctly to get the right flavour profile. The pump can handle cold water and glycol.To be able to cool with the Grainfather Conical Fermenter, you need to have the Conical Fermenter Temperature Controller. Then once your target temperature is below the temperature of the wort in your fermenter the Cooling Pump Kit pumps ice cold water or Glycol through the double walled insulated interior to cool down your wort. Simply connect the couplers and insulated hoses to the Conical Fermenter, submerge the submersible pump into a cooler box with water (add ice for your required temperature) and pump the liquid through the insulated cooling sleeve of the Conical Fermenter body.- Conical Fermenter Cooling Pump (submersible) that can handle Glycol.- T-section power connector.- 2 x brass couplers.- Rated 12 VDC – 4.8 Watts.

€75 €85
DEAL
Grainfather Pressure Transfer Kit

Grainfather Pressure Transfer Kit

All you need is a C02 bottle and a regulator to attach to the Pressure Transfer and you can transfer your beer into a keg or bottles through the Conical Fermenter Dual Valve Tap or via the top of the fermenter lid using the Beer Racking Pipe.Package includes- High quality 304 stainless steel components- Accurate digital pressure gauge- Needle valve for precise control of pressureNOTE: Batteries are not included for the Pressure Gauge. 2 x AAA batteries are needed.

€89
Glass Jar with Lid & Tapp 4L

Glass Jar with Lid & Tapp 4L

Glass jar 4L with lid and tap with many uses, such as: fermentation of beverages such as Kombucha, for cold beverages such as beer, cider, wine, juice, ice water or lemonade.Note: During fermentation, the lid must be slightly open, with eg. a muslin bag in between. The lid must be opened a little to make the tap work, this is due to that a vacuum is formed in the glass when the lid is on. Must NOT be pressurized.- Capacity: 4 liters- Dimensions (approx.): 27 x 16 x 16.5 cm (HxWxD)- With lid and tap.- Hand wash only.- Not for hot drinks.

€14
Brewtools MiniUni 10L

Brewtools MiniUni 10L

Brewtools MiniUni 10LThe MiniUni™ tanks are a range of high quality flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as heating water, storing cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EU Specification:Pack size: 34 (w) x 34(d) x 61 (h) cmWeight without emaballage: 8 KgWeight with packaging: 9.3 KgTank diameter (inside): Ø28 cmMax. recommended volume: 10 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSIThis comes with: MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-part with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

€299
FermZilla Tri-Conical Gen3 Starter Kit 27L Fermenter

FermZilla Tri-Conical Gen3 Starter Kit 27L Fermenter

Now with Tri-Clover Clamp for easy assembly and disassembly of the conical tank, Butterfly valve and harvesting container. No more difficult and complicated Butterfly valve. Now it is easy and simple to mount Butterfly valve with the Tri-Clover Clamp. See video below.FermZilla revolutionary design simplifies the home brewing process and minimizes the risks of infection and oxidation. Finally, you can brew your beer and dispense directly to bottles or drink it as draft beer – without touching the beer. You can carbonate your beer naturally in the FermZilla, or at your desired pressure with the optional pressure kit and the additional pressure release valve with gauge.Facts:27 L. Conical tankWorking pressure: 2.4 bar (35 psi)FermZilla Tri-Conical Starter kit Gen-3 - 27 L. contains:1 x 27 L. Conical tank with metal neck ring1 x Butterfly valve with Tri-Clover Clamps1 x 3" Tri-Clover Clamp1 x 2" Tri-Clover Clam1 x Reinforced stainless steel frame1 x Lidt with red pressure release valve 2,4 bar/35 psi, 2 x Male Cap Threads, with caps and the possibility to drill 4 ports for accessories1 x  1000 ml yeast harvesting container with 2 x Male Cap Threads and caps.1 x Airlock1 x Stainless Steel Handle Assembly1 x Strip Stick On Thermometer1 x Level indicator sticker (Litres and Gallons)1 x Spare O-RingDo not expose to liquid temperatures above 55°C / 130°F or ambient temperatures above 35°C / 95°F.Instructions manualClick hereWarnings:Please read instructions thoroughly before use. The current version can be found in the 'instructions' tab above. We will not be held liable for misuse or mishandling of the unit contrary to the instructions.Do not expose to liquid temperatures above 55°C / 130°F or ambient temperatures above 35°C / 95°F.

€158
Temporarily out of stock
View product
FermZilla Tri-Conical Gen3 Starter Kit 55L Fermenter

FermZilla Tri-Conical Gen3 Starter Kit 55L Fermenter

Now with Tri-Clover Clamp for easy assembly and disassembly of the conical tank, Butterfly valve and harvesting container. No more difficult and complicated Butterfly valve. Now it is easy and simple to mount Butterfly valve with the Tri-Clover Clamp. See video below.FermZilla revolutionary design simplifies the home brewing process and minimizes the risks of infection and oxidation. Finally, you can brew your beer and dispense directly to bottles or drink it as draft beer – without touching the beer. You can carbonate your beer naturally in the FermZilla, or at your desired pressure with the optional pressure kit and the additional pressure release valve with gauge.Facts:55 L. Conical tankWorking pressure: 2.4 bar (35 psi)FermZilla Tri-Conical Starter kit Gen-3 - 55 L. contains:1 x 27 L. Conical tank with metal neck ring1 x Butterfly valve with Tri-Clover Clamps1 x 3" Tri-Clover Clamp1 x 2" Tri-Clover Clam1 x Reinforced stainless steel frame1 x Lidt with red pressure release valve 2,4 bar/35 psi, 2 x Male Cap Threads, with caps and the possibility to drill 4 ports for accessories1 x  1000 ml yeast harvesting container with 2 x Male Cap Threads and caps.1 x Airlock1 x Stainless Steel Handle Assembly1 x Strip Stick On Thermometer1 x Level indicator sticker (Litres and Gallons)1 x Spare O-RingDo not expose to liquid temperatures above 55°C / 130°F or ambient temperatures above 35°C / 95°F.Instructions manualClick hereWarnings:Please read instructions thoroughly before use. The current version can be found in the 'instructions' tab above. We will not be held liable for misuse or mishandling of the unit contrary to the instructions.Do not expose to liquid temperatures above 55°C / 130°F or ambient temperatures above 35°C / 95°F.

€178 €187
DEAL
Temporarily out of stock
View product
FermZilla All Rounder 30L Fermenter

FermZilla All Rounder 30L Fermenter

The FermZilla 30L All Rounder is the perfect fermentation vessel that can be used for fermenting under pressure, carbonating and dispensing. Incl. Fermenter body, stainless steel frame, airlock and lid with red pressure relief valve. Pressure rated up to 2.5bar.This kit includes:1 x All rounder tank1 x 304 stainless stand1 x Airlock1 x Pressure rated lid1 x Digital temperature sticker1 x Red 2.5bar pressure relief valve1 x Graduation StickerEasy to CleanThis fermenter is made from super smooth PET so it's easy to clean. Just use s small scoop of Powerful Brewery Wash and wipe it clean after a 5 minute soak. No scrubbing necessary.Large 120mm OpeningThe opening at the top is signficantly larger then the older Snub Nose or other similar fermenters. This bad boy has 120mm opening so even brewers with large arms can easily get into the top making cleaning even easier.Pressure RatedThis fermenter is rated up to 2.5bar so you can force carbonate just like a keg. You can use this fermenter for closed transfers and signficiantly reduce oxygen exposure.Crystal ClearThe wall of the All Rounder is crystal clear so you can see what's going on inside. This makes it really easy to determine visually how the fermentation, how the yeast is floculating etc.ImpermeableThe PET plastic is not permeable like some other fermenters made from PP or HDPE. The fermenter wall is a much better gas barrier keeping your product fresher for longer.No Flavour and Aroma Carry OverOther HDPE fermenters tend to be so pourous they carry flavour and aromo from one batch to another. Robust and Difficult to DamageImpossible to smash like glass. The tank is impact resistant but light weight and easy to use.IMPORTANT NOTE: This tank should not be used for hot liquid. Do not put liquids inside this tank over 50C. It will melt the tank. Also this tank comes pressure tested however we recommend that every 2 years you re-hydro test this tank yourself. Please contact us for more information regarding how to hydro test when the time comes.

€85
Temporarily out of stock
View product
FermZilla All Rounder 60L Fermenter

FermZilla All Rounder 60L Fermenter

The FermZilla 60L All Rounder is the perfect fermentation vessel that can be used for fermenting under pressure, carbonating and dispensing. Incl. Fermenter body, stainless steel frame, airlock and lid with red pressure relief valve. Pressure rated up to 2.5bar.This kit includes:1 x All rounder tank1 x 304 stainless stand1 x Airlock1 x Pressure rated lid1 x Digital temperature sticker1 x Red 2.5bar pressure relief valve1 x Graduation StickerEasy to CleanThis fermenter is made from super smooth PET so it's easy to clean. Just use s small scoop of Powerful Brewery Wash and wipe it clean after a 5 minute soak. No scrubbing necessary.Large 120mm OpeningThe opening at the top is signficantly larger then the older Snub Nose or other similar fermenters. This bad boy has 120mm opening so even brewers with large arms can easily get into the top making cleaning even easier.Pressure RatedThis fermenter is rated up to 2.5bar so you can force carbonate just like a keg. You can use this fermenter for closed transfers and signficiantly reduce oxygen exposure.Crystal ClearThe wall of the All Rounder is crystal clear so you can see what's going on inside. This makes it really easy to determine visually how the fermentation, how the yeast is floculating etc.ImpermeableThe PET plastic is not permeable like some other fermenters made from PP or HDPE. The fermenter wall is a much better gas barrier keeping your product fresher for longer.No Flavour and Aroma Carry OverOther HDPE fermenters tend to be so pourous they carry flavour and aromo from one batch to another. Robust and Difficult to DamageImpossible to smash like glass. The tank is impact resistant but light weight and easy to use.IMPORTANT NOTE: This tank should not be used for hot liquid. Do not put liquids inside this tank over 50C. It will melt the tank. Also this tank comes pressure tested however we recommend that every 2 years you re-hydro test this tank yourself. Please contact us for more information regarding how to hydro test when the time comes.

€103
Temporarily out of stock
View product
FermZilla Flat Bottom 30L Fermenter

FermZilla Flat Bottom 30L Fermenter

The FermZilla Flat Bottom 30L is the perfect fermentation vessel that can be used for fermenting. Incl. Fermenter body, airlock and lid with red pressure relief valve. Note:This fermenter has not been pressure rated and it's not designed to carbonate in.  If you are looking for a pressure rated fermenter that you can carbonate in then we would recommend that you go for the "FermZilla All-Rounder" Or "FermZilla Uni Tank" models.  For this reason, we have not supplied this tank with a PRV valve.  With that said the actual tank body is able to hold approximately 2psi.  (so almost no pressure at all)This kit includes:1 x Flat Bottom tank1 x Airlock1 x LidEasy to CleanThis fermenter is made from super smooth PET so it's easy to clean. Just use s small scoop of Powerful Brewery Wash and wipe it clean after a 5 minute soak. No scrubbing necessary.Large 120mm OpeningThe opening at the top is signficantly larger then the older Snub Nose or other similar fermenters. This bad boy has 120mm opening so even brewers with large arms can easily get into the top making cleaning even easier.Crystal ClearThe wall of the All Rounder is crystal clear so you can see what's going on inside. This makes it really easy to determine visually how the fermentation, how the yeast is floculating etc.ImpermeableThe PET plastic is not permeable like some other fermenters made from PP or HDPE. The fermenter wall is a much better gas barrier keeping your product fresher for longer.No Flavour and Aroma Carry OverOther HDPE fermenters tend to be so pourous they carry flavour and aromo from one batch to another. Robust and Difficult to DamageImpossible to smash like glass. The tank is impact resistant but light weight and easy to use.IMPORTANT NOTE: This tank should not be used for hot liquid. Do not put liquids inside this tank over 50C. It will melt the tank. Also this tank comes pressure tested however we recommend that every 2 years you re-hydro test this tank yourself. Please contact us for more information regarding how to hydro test when the time comes.

€47
Temporarily out of stock
View product
FermZilla Stainless Pressure Kit

FermZilla Stainless Pressure Kit

Add this pressure kit to your FermZilla 27L, 35L or 55L and turn your FermZilla into a true uni tank that can be used for carbonating beer. Stainless steel.This inexpensive upgrade will truly show you what the FermZilla was designed for. Here are some possibilities:Fermenting Under Pressure:First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. Carbonating, Pushing, and Serving:When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator. Lack of OxidationBecause the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock. Key Features:• Ferment beer under pressure to reduce ester and fusel alcohol production• Ability to always draw clear beer with the unique, floating draw tube • Keg already carbonated beer• Use co2 to push beer into a keg or though a filter into a keg• Carbonate and serve beer directly from the FermZilla, eliminating kegging all togetherFermZilla Stainless Pressure Kit includes:- 2 x Carbonation Screw Caps with barb- 1 x FermZilla 27L, 35L & 55L SS Floar & 60cm Silicone Dip Tube

€37
FermZilla Stainless Steel Carbonation/Cleaning Cap

FermZilla Stainless Steel Carbonation/Cleaning Cap

Fits CO2/Beer Ball-lock-coupling. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Stainless steel.

€18
FermZilla Red Plastic Carbonation/Cleaning Cap

FermZilla Red Plastic Carbonation/Cleaning Cap

Fits CO2/Beer Ball-lock-coupling. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Red plastic.

€5,5
FermZilla Twister Cooling Spiral

FermZilla Twister Cooling Spiral

Fermzilla chiller. Provides the possibility of temperature control during fermentation using, for example, glycol coolers. Of course, the spiral also fits in other vessels with sufficiently large opening. Are installed by drilling two 22 mm holes in the lid. It is attached using the supplied Duotight bushings. The tube dimension is compatible with 3/8 "(9.5 mm) quick couplings. The length can be reduced by means of a pipe cap. See proposed accessories below.

€45
FermZilla Thermowell 60cm

FermZilla Thermowell 60cm

Thermowell of 60 cm for mounting in the lid of Fermzilla. Inner diameter is 7 mm, enough room for most temperature probes such as Inkbird.

€15
FermZilla 27L Insulation Jacket

FermZilla 27L Insulation Jacket

Insulated Jacket for Fermzilla 27L designed to insulate your FermZilla and to obtain a correct temperature.

€38
FermZilla 55L Insulation Jacket

FermZilla 55L Insulation Jacket

Insulated Jacket for Fermzilla 55L designed to insulate your FermZilla and to obtain a correct temperature.

€47
FermZilla Yeast Collector 1L

FermZilla Yeast Collector 1L

This yeast collection container can fit the FermZilla fermenters and is primarily used for collection and addition of hops and yeast via the butterfly valve. NOTE: One yeast collector is already included in the FermZilla Kits.This collection container can also be used for yeast starters meaning that you can create the yeast starter in this collection container directly then attach to the valve of the FermZilla so you can pitch yeast without needing to open the lid. This collection container has been designed to work with the magnetic stirrer machine.The ports on the side of this collection container are the same as a standard coke bottle or soft drink bottle. The threads are designed to suit the stainless carbonation caps. These carbonation caps will enable you to purge oxygen for dry hopping, attach carbonation stone and carbonate liquid in the FermZilla, oxygenate wort and are useful for many other reasons.FermZilla Yeast Collector 1L features:- This collection container fits all the FermZilla conical fermenters.- The clear body is made from Tritan from Eastman Plastics. This heat tolerant plastic is BPA, and plasticiser free.- The Lid is made from impact resistant HDPE.- Both lid and body can handle boiling wort.- Height: 150 mm- Diameter: 115 mm- Capacity: 1L

€24
Temporarily out of stock
View product
FermZilla Yeast Collector O-ring Packning

FermZilla Yeast Collector O-ring Packning

FermZilla Yeast Collector O-ring Packning. Spare part.

€4,6
FermZilla Plastic Lid

FermZilla Plastic Lid

FermZilla Plastic Lid. Spare part.

€14
Fermzilla Lid Ring

Fermzilla Lid Ring

Fermzilla Lid Ring replacement part.

€14
Temporarily out of stock
View product
FermZilla Lid Seal O-ring

FermZilla Lid Seal O-ring

Spare part. FermZilla Lid Seal O-ring. Fits FermZilla 27L, 35L and 55L.

€2,7
Temporarily out of stock
View product
Fermzilla Conical Valve Assembly

Fermzilla Conical Valve Assembly

Fermzilla Conical Valve Assembly with the conical plastic part, conical gasket, O-ring and Threaded lid ring.

€16
Temporarily out of stock
View product
Ferminator Connect - Wifi & Bluetooth Thermostat Controlled Cooler

Ferminator Connect - Wifi & Bluetooth Thermostat Controlled Cooler

We have taken all the best from Ferminator Basic and made a new version with WiFi and Bluetooth. It is now possible to control your Ferminator online and see current temperatures and settings. In BrewCreator you can enter data about your brew and see all information about your Ferminator Connect. The whole thing is gathered in a nice detailed graph, where you can follow the course of the temperature and see the changes that have been made. Ferminator Connect can also communicate directly with Graviator - a wireless hydrometer measuring directly inside your fermenter (bought seperately). At room temperature (20 °) the temperature can be lowered to 0 ° or increased to 50 ° *. A powerful thermoelectric Peltier element that stands for the cold, the fan dissipates the heat generated in the process. The height of the Ferminator can be easily expanded with 22cm high expansion modules that are purchased separately. In the Basic version, there is room for, for example, a 30L plastic fermenter or a 30L Fermzilla Flat Bottom. Ferminator Ferminator is a revolution in temperature-controlled fermentation. With a Ferminator it is now possible to ferment at a precise and stable temperature. At room temp. (20 °) the Ferminator can lower the temp. to 0 ° and raise it to 50 ° *. The height can easily be extended with optional 22cm high expansion modules (buy seperately). - The Ferminator makes is possible to ferment at the precise desired temperature. For example, it is possible to ferment a pilsner or lager at the proper low temperature or an ale at high temperature to achieve lots of desired esters. - The Ferminator keeps the temperature constant during the fermentation process and can of course be adjusted at any time. A constant fermentation temperature ensures unwanted flavor notes can be avoided and that the yeast will go into a hibernation state. - The Ferminator gives you full control over the fermentation and lets you experiment with completely new flavor notes and profiles. Cooling / Heating Unit - At room temperature (20 ° C) the Ferminator can lower the temperature to 0C and raise the temperature to 50 ° C *. - Lowers temperature down to 20 ° C relative to ambient temp *. - Raises the temperature up to 30 ° C relative to ambient temp *. - The built-in fan ensures evenly temperature throughout the Ferminator. - The control unit is easily programmed and displays the actual temperature and set temperature. - The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid. - Maximum power consumption: 75 Watts, standby: 1 Watt. * Tested with Ferm inator Basic, when using expansion modules, an additional Cooling / Heating Unit may be required. Ferminator Connect - Dimensions outside: 560 L x 560 B x 651 H - Dimensions inside: 436 L x 436 W x 531 H Size fits: 32 L. Fermenter 30 L. FermZilla Flat Bottom Material Ferminator is made in EPS. Optional Expansion (Not Included, buy it seperately below) Expansion Module The expansion module has a height of 22 cm. The Ferminator can be expanded with several expansion modules an additional cooling / heating unit on the back. The expansion module and Ferminator can be disassembled taking up minimal storage space. Note that some product images contain extra equipment not included.

€346
Ferminator Basic Thermostat Controlled Cooler

Ferminator Basic Thermostat Controlled Cooler

Ferminator is a revolution in temperature-controlled fermentation. With a Ferminator it is now possible to ferment at a precise and stable temperature. At room temp. (20°) the Ferminator can lower the temp. to 0° and raise it to 50°*. The height can easily be extended with optional 22cm high expansion modules (buy seperately).The Ferminator makes is possible to ferment at the precise desired temperature. For example, it is possible to ferment a pilsner or lager at the proper low temperature or an ale at high temperature to achieve lots of desired esters.The Ferminator keeps the temperature constant during the fermentation process and can of course be adjusted at any time. A constant fermentation temperature ensures unwanted flavour notes can be avoided and that the yeast will go into a hibernation state.The Ferminator gives you full control over the fermentation and lets you experiment with completely new flavour notes and profiles.Cooling/Heating Unit- At room temperature (20°C) the Ferminator can lower the temperature to 0C and raise the temperature to 50°C*.- Lowers temperature down to 20°C relative to ambient temp*.- Raises the temperature up to 30°C relative to ambient temp*.- The built-in fan ensures evenly temperature throughout the Ferminator.- The control unit is easily programmed and displays the actual temperature and set temperature.- The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid.- Maximum power consumption: 75 Watts, standby: 1 Watt. *Tested with Ferminator Basic, when using expansion modules, an additional Cooling/Heating Unit may be required.Ferminator Basic- Dimensions outside: 560 L x 560 B x 651 H- Dimensions inside: 436 L x 436 B x 531 HSize fits:32 L. Fermenter30 L. FermZilla Flat Bottom MaterialFerminator is made in EPS.Optional Expansion (Not Included, buy it seperately below)Expansion ModuleThe expansion module has a height of 22 cm.The Ferminator can be expanded with several expansion modules an additional cooling/ heating unit on the back. The expansion module and Ferminator can be disassembled taking up minimal storage space.Note that some product images contain extra equipment not included.

€299
Temporarily out of stock
View product
Ferminator Basic Kit 1 Thermostat Controlled Cooler

Ferminator Basic Kit 1 Thermostat Controlled Cooler

Ferminator with one expansion module. Ferminator is a revolution in temperature-controlled fermentation. With a Ferminator it is now possible to ferment at a precise and stable temperature. At room temp. (20°) the Ferminator can lower the temp. to 0° and raise it to 50°*. The height can easily be extended with optional 22cm high expansion modules (buy seperately).The Ferminator makes is possible to ferment at the precise desired temperature. For example, it is possible to ferment a pilsner or lager at the proper low temperature or an ale at high temperature to achieve lots of desired esters.The Ferminator keeps the temperature constant during the fermentation process and can of course be adjusted at any time. A constant fermentation temperature ensures unwanted flavour notes can be avoided and that the yeast will go into a hibernation state.The Ferminator gives you full control over the fermentation and lets you experiment with completely new flavour notes and profiles.Cooling/Heating Unit- At room temperature (20°C) the Ferminator can lower the temperature to 0C and raise the temperature to 50°C*.- Lowers temperature down to 20°C relative to ambient temp*.- Raises the temperature up to 30°C relative to ambient temp*.- The built-in fan ensures evenly temperature throughout the Ferminator.- The control unit is easily programmed and displays the actual temperature and set temperature.- The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid.- Maximum power consumption: 75 Watts, standby: 1 Watt. *Tested with Ferminator Basic, when using expansion modules, an additional Cooling/Heating Unit may be required.Ferminator Basic Kit 1- Dimensions outside: 560 L x 560 B x 871 H- Dimensions inside: 436 L x 436 B x 751 HSize fits:32 L. Fermenter, 3pcs Cornelius kegs or Fermzilla Allrounder 30LMaterialFerminator is made in EPS.Optional Expansion (Not Included, buy it seperately below)Expansion ModuleThe expansion module has a height of 22 cm.The Ferminator can be expanded with several expansion modules an additional cooling/ heating unit on the back. The expansion module and Ferminator can be disassembled taking up minimal storage space.Note that some product images contain extra equipment not included.

€318
Temporarily out of stock
View product
Ferminator Basic Kit 2 Thermostat Controlled Cooler

Ferminator Basic Kit 2 Thermostat Controlled Cooler

Ferminator with two expansion modules. Ferminator is a revolution in temperature-controlled fermentation. With a Ferminator it is now possible to ferment at a precise and stable temperature. At room temp. (20°) the Ferminator can lower the temp. to 0° and raise it to 50°*. The height can easily be extended with optional 22cm high expansion modules (buy seperately).The Ferminator makes is possible to ferment at the precise desired temperature. For example, it is possible to ferment a pilsner or lager at the proper low temperature or an ale at high temperature to achieve lots of desired esters.The Ferminator keeps the temperature constant during the fermentation process and can of course be adjusted at any time. A constant fermentation temperature ensures unwanted flavour notes can be avoided and that the yeast will go into a hibernation state.The Ferminator gives you full control over the fermentation and lets you experiment with completely new flavour notes and profiles.Cooling/Heating Unit- At room temperature (20°C) the Ferminator can lower the temperature to 0C and raise the temperature to 50°C*.- Lowers temperature down to 20°C relative to ambient temp*.- Raises the temperature up to 30°C relative to ambient temp*.- The built-in fan ensures evenly temperature throughout the Ferminator.- The control unit is easily programmed and displays the actual temperature and set temperature.- The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid.- Maximum power consumption: 75 Watts, standby: 1 Watt. *Tested with Ferminator Basic, when using expansion modules, an additional Cooling/Heating Unit may be required.Ferminator Basic Kit 2- Dimensions outside: 560 L x 560 B x 1091 H- Dimensions inside: 436 L x 436 B x 971 HSize fits:32 L. Fermenter, 4pcs Cornelius kegs or Fermzilla Allrounder 30L & 50L, fermzilla 27L & 35L, Brewly 30L conical fermenter.MaterialFerminator is made in EPS.Optional Expansion (Not Included, buy it seperately below)Expansion ModuleThe expansion module has a height of 22 cm.The Ferminator can be expanded with several expansion modules an additional cooling/ heating unit on the back. The expansion module and Ferminator can be disassembled taking up minimal storage space.Note that some product images contain extra equipment not included.

€337
Temporarily out of stock
View product
Ferminator Basic Kit 3 Thermostat Controlled Cooler

Ferminator Basic Kit 3 Thermostat Controlled Cooler

Ferminator with three expansion modules. Ferminator is a revolution in temperature-controlled fermentation. With a Ferminator it is now possible to ferment at a precise and stable temperature. At room temp. (20°) the Ferminator can lower the temp. to 0° and raise it to 50°*. The height can easily be extended with optional 22cm high expansion modules (buy seperately). Fits for example a 55L Fermzilla.FerminatorFerminator is a revolution in temperature-controlled fermentation. With a Ferminator it is now possible to ferment at a precise and stable temperature. At room temp. (20°) the Ferminator can lower the temp. to 0° and raise it to 50°*. The height can easily be extended with optional 22cm high expansion modules (buy seperately).- The Ferminator makes is possible to ferment at the precise desired temperature. For example, it is possible to ferment a pilsner or lager at the proper low temperature or an ale at high temperature to achieve lots of desired esters.- The Ferminator keeps the temperature constant during the fermentation process and can of course be adjusted at any time. A constant fermentation temperature ensures unwanted flavour notes can be avoided and that the yeast will go into a hibernation state.- The Ferminator gives you full control over the fermentation and lets you experiment with completely new flavour notes and profiles.Cooling/Heating Unit- At room temperature (20°C) the Ferminator can lower the temperature to 0C and raise the temperature to 50°C*.- Lowers temperature down to 20°C relative to ambient temp*.- Raises the temperature up to 30°C relative to ambient temp*.- The built-in fan ensures evenly temperature throughout the Ferminator.- The control unit is easily programmed and displays the actual temperature and set temperature.- The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid.- Maximum power consumption: 75 Watts, standby: 1 Watt. *Tested with Ferminator Basic, when using expansion modules, an additional Cooling/Heating Unit may be required.Ferminator Basic Kit 3- Dimensions outside: 560 L x 560 B x 1311 H- Dimensions inside: 436 L x 436 B x 1191 HSize fits: 55L FermzillaMaterialFerminator is made in EPS.Optional Expansion (Not Included, buy it seperately below)Expansion ModuleThe expansion module has a height of 22 cm.The Ferminator can be expanded with several expansion modules an additional cooling/ heating unit on the back. The expansion module and Ferminator can be disassembled taking up minimal storage space.Note that some product images contain extra equipment not included.

€356
Temporarily out of stock
View product
Ferminator Bottom Stainless Steel Plate

Ferminator Bottom Stainless Steel Plate

Protects the bottom of the Ferminator. The bottom plate has rounded corners and is made of stainless steel.

€33
Ferminator Bottom

Ferminator Bottom

Ferminator Bottom Spare part.

€28
Ferminator Basic Cooling & Heating Unit

Ferminator Basic Cooling & Heating Unit

The Ferminator can be expanded with an additional cooling/ heating unit on the back, so you have two units that can regulate the temperature. This is a Ferminator Basic unit. At room temperature (20°) the temperature can be lowered to 0 ° or increased to 50 ° *. A powerful thermoelectric Peltier element that stands for the cold, the fan dissipates the heat generated in the process. Ferminator Basic Cooling & Heating Unit - At room temperature (20°C) the Ferminator can lower the temperature to 0C and raise the temperature to 50 ° C *. - Lowers temperature down to 20 ° C relative to ambient temp *. - Raises the temperature up to 30 ° C relative to ambient temp *. - The built-in fan ensures evenly temperature throughout the Ferminator. - The control unit is easily programmed and displays the actual temperature and set temperature. - The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid. - Maximum power consumption: 75 Watts, standby: 1 Watt. * Tested with Ferm inator Basic, when using expansion modules, an additional Cooling / Heating Unit may be required. Note that some product images contain extra equipment not included.

€243
Temporarily out of stock - Advance booking available
View product
Ferminator Connect Cooling & Heating Unit

Ferminator Connect Cooling & Heating Unit

The Ferminator can be expanded with an additional cooling/ heating unit on the back, so you have two units that can regulate the temperature. This is a Ferminator Connect unit which can be connected to WiFi and be controlled online by BrewCreator.We have taken all the best from Ferminator Basic and made a new version with WiFi and Bluetooth. It is now possible to control your Ferminator online and see current temperatures and settings. In BrewCreator you can enter data about your brew and see all information about your Ferminator Connect. The whole thing is gathered in a nice detailed graph, where you can follow the course of the temperature and see the changes that have been made. Ferminator Connect can also communicate directly with Graviator - a wireless hydrometer measuring directly inside your fermenter (bought seperately). At room temperature (20°) the temperature can be lowered to 0 ° or increased to 50 ° *. A powerful thermoelectric Peltier element that stands for the cold, the fan dissipates the heat generated in the process. Ferminator Connect Cooling & Heating Unit - Wifi & Bluetooth- At room temperature (20°C) the Ferminator can lower the temperature to 0C and raise the temperature to 50 ° C *. - Lowers temperature down to 20 ° C relative to ambient temp *. - Raises the temperature up to 30 ° C relative to ambient temp *. - The built-in fan ensures evenly temperature throughout the Ferminator. - The control unit is easily programmed and displays the actual temperature and set temperature. - The temperature sensor can be mounted either on or inside the fermentation unit with a thermowell thereby measuring the precise temperature of the liquid. - Maximum power consumption: 75 Watts, standby: 1 Watt. * Tested with Ferm inator Basic, when using expansion modules, an additional Cooling / Heating Unit may be required. Note that some product images contain extra equipment not included.

€281
Ferminator Plug & Pour Drip Tray - 2 Taps

Ferminator Plug & Pour Drip Tray - 2 Taps

Upgrade the Ferminator to a fullblood draft beer system with a simple plug and then pour craft beer straight away. Plug & Pour is an easy solution for transforming the Ferminator to a draft beer system with 2 taps.The following is included in Ferminator Plug & Pour Drip Tray - 2 Taps:• Plug & Pour mounting plate• Ferminator Drip Tray• Ferminator Strap• Ferminator Insert• 2 xTaps with flow control• 2 x Shanks• 2 x Ball Locks fluid• 2 x Ball Locks Co2 • Tube for liquid• Tube for Co2• Doutight fittings• T-Piece for Co2

€281
Ferminator Strap

Ferminator Strap

The strap holds the top together, ideal if the Ferminator needs to be moved. Can also be ideal when using an extra cooling/heating unit or Plug & Pour.

€7,4
Graviator - Wireless Wifi & Bluetooth Hydrometer

Graviator - Wireless Wifi & Bluetooth Hydrometer

A wireless hydrometer and thermometer that measures directly in the fermenter, and comminicates to the app BrewConnect via WiFi. It can be used independently in a brewing via WiFi, but the extra smart thing is that it can communicate directly with Ferminator Connect via Bluetooth. This allows a Ferminator Connect to know the exact temperature inside the beer and adjust the temperature even more precisely. The Gravity charger is charged wirelessly via the included wireless charger. It should therefore never be opened, and you avoid the risk of it leaking and destroying a brew. If the Graviator is not charged before brewing, this is not a problem. It can be charged in approx. 5 hours. The improved algorithm in Graviator, the unique design and build quality provide a high accuracy of ± 0.002 SG. The size and weight of the engraver also make it more stable under the crotch.

€150
Graviator - Wireless Charger

Graviator - Wireless Charger

Graviator Wireless Charger can charge a Graviator of approx. 5 hours. The charger follows the Qi standard and can charge with 5W / 7.5W / 10W. This charger will also work with your phone if it's Qi-enabled.

€13
RAPT Pill Replacement Silicone O-Ring

RAPT Pill Replacement Silicone O-Ring

Replacement Silicone O-ring for RAPT Pill. It is a good idea to use keg lube to keep these o-rings in the best conditions

€3,6
MiniBrew Smart Keg 3.0

MiniBrew Smart Keg 3.0

Thirsty for more? Expand your brewing capabilities by adding more Smart Kegs to your collection. Satisfy the urge to brew again while your other Smart Kegs are occupied; fulfill the increasing fresh beer demands of your friends, family, and colleagues; and enjoy a variety of beer styles on tap at the same time.What's newIntroducing a two turn-lock mechanism -  it becomes easy to turn the lid into the kegImproved cooling - we redesigned the Peltier element that handles better air pressure when switching between heat and cold. Added a new coating - which makes the keg more fluid and dust resistant and easier to clean. Updated the power adapter casing - It's more resistant to ensure that in severe cases the power adapter will survive.What’s in the box?1 x Smart Keg inc P ressure Relieve Valve + beer tube2x ball lock connectors1x beer tap1x Co2 regulator (psi)1x Airlock + rubber stopper1 x Power Supply  (110-240V with EU power plug)1 x Keg Stand1x trub container2-year warranty

€318 €371
DEAL
Pressure Valve with Manometer 2 Bar

Pressure Valve with Manometer 2 Bar

Adjustable pressure valve with manometer. Can handle pressures up to 2 bar / 30 psi. 1/4" MFL.

€24
FermZilla Hydro Pressure Test Adapter

FermZilla Hydro Pressure Test Adapter

As the FermZilla/Fermentasaurus containers are a pressure vessel thus they require periodic testing. We recommend that you pressure test the Fermentasaurus containers once every 2 years if you want to keep using the fermenter under pressure. This fitting allows you to hydrostatically pressure test the FermZilla/fermentasaurus tank using a keg and regulator. First fill the fermzilla/fermentasaurus to the brim with tap water. This fitting will screw into the pressure relief valve socket on the pressure lid for the fermzilla/fermentersaurus. You would then connect a swivel nut and barb to this fitting, connected to the luqid out of a keg full of water. You can then connect your regulator to the gas in on the keg and pressurises the system to the test pressure.

€14
Temporarily out of stock
View product
Fermentasaurus Insulated Jacket 35L

Fermentasaurus Insulated Jacket 35L

This jacket is designed to insulate your Fermentasaurus during the colder months to keep your fermentation at the optimum temperature. It can also be used with a heating belt/wrap to warm up the wort if the heat from the fermentation isn't enough.Also completely blocks any light/UV to prevent light-struck beer.

€56
EcoStir Magnetic Stirrer

EcoStir Magnetic Stirrer

Easy-to-use magnetic stirrer with good capacity. Infinitely variable speed and durable plastic construction that can withstand a little spill. Rotatable stand for e.g. thermometer or pH probe included. Stable base with rubber feet. Ultra silence and vibration-free design. Stackable, which saves space during storage.Material: Durable plastic cover.Speed: Stepless 300-2000 rpm.Capacity: 1.5 liters.Power supply: 12V from the included 230V mains adapter.Max Power: 7,2WDimensions: Diameter top 120 mm, max 160 mm. Height 55 mm without stand, 230 mm with stand.Weight: 300 g.Protection class: IP21Accessories: Stand with holder (for probe max 12 mm) included.

€93
Fisher Scientific Magnetic Stirrer

Fisher Scientific Magnetic Stirrer

This is a simple, reliable and efficient magnetic stirrer for up to 5L flasks. Excellent speed precision. Remains cold even after several days of continuous use. Ensures a high resistance to chemical agents. - High Reliability- Control panel is shielded from liquid spills- Epoxy-coated tough steel casing- Long life operation- Accepts up to 5 liter flasksFeatures- Pale surface for visualization of particles and color changes- Remains cold, even after days of continuous use- Specifically designed for microtitration- Excellent speed control, even at low speed- Simple & Practical- Precision speed regulation up to 1100rpm- Universal mains voltage / frequency range- Light weightTechnical data: Fisher Scientific Microstirrer Magnetic StirrerHeight: 48mmWeight: 0.55KgSpeed: up to 1100RPMMaterial: Epoxy, MetalSpeed Control: Excellent speed control even at low revolutionsSize: 48 H x 120 W x 128 DmmWattage: 0.6WWidth: 120mmVoltage: 100-240VHertz: 50/60HzElectrical Requirements: 100 to 240V, 50/60Hz, 0.6W

€150 €187
DEAL
Temporarily out of stock
View product
Wort Whipper - Compact Magnetic Stirrer

Wort Whipper - Compact Magnetic Stirrer

Compact magnetic stirrer machine with adjustable speed. Perfect as a yeast starter and propagation of your yeast, up to 3 liters. Power 3W, adaptor with EU-outlet included (12VDC/220V, 1.2m cord). 1pc Magnetic Stir Bar included.

€70
Brewly Stainless Steel Tap

Brewly Stainless Steel Tap

Tap made in 304 stainless steel that fits most breweries. Rubber covered handle with auto-lock function. 1/2" thread with stainless 1/2" nut and silicone seal. 13mm barb at the opening.Tappkran i rostfritt stål som passar de flesta bryggverk. Gummitäckt handtag med autolåsfunktion. 1/2" gänga och levereras med rostfri 1/2" mutter samt silikonpackning. 13mm nippel på utloppet. Tillverkad i 304-rostfritt stål.

€16 €24
DEAL
Temporarily out of stock
View product
Fisher PTFE Stir Bar 40x8mm

Fisher PTFE Stir Bar 40x8mm

Provides stable stirring action. The PTFE magnetic stir bar work within a wide range of conditions. Smooth, round profile for a wide variety of applications. White PTFE encapsulated Alnico V magnet core. Autoclavable.MeasurementsLength: 40 mmDiameter: 8 mm

€3,6
Pyrex Erlenmeyer Flask 250ml

Pyrex Erlenmeyer Flask 250ml

Original Pyrex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Pyrex Borosilicate glass. Idal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.- Complies with DIN ISO 24450- Erlenmeyer pattern- Manufactured from Pyrex borosilicate glass- Excellent thermal performance- High resistance to chemical attack- White enamel graduations and marking spot- Graduated to capacity- Printed with Trace Code for downloadable batch certificate- Batch certificate available to download from www.scilabware.com- Made in Great BritainPyrex Wide-Neck Erlenmeyer Flask 250mlVolume: 250 mlDiameter: 85 mm (at the base)Height: 140 mmOpening inner diameter: 46 mm

€16
Volume discount! €16 per piece when you buy 2 or more
Pyrex Erlenmeyer Flask 500ml

Pyrex Erlenmeyer Flask 500ml

Original Pyrex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Pyrex Borosilicate glass. Idal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.- Complies with DIN ISO 24450- Erlenmeyer pattern- Manufactured from Pyrex borosilicate glass- Excellent thermal performance- High resistance to chemical attack- White enamel graduations and marking spot- Graduated to capacity- Printed with Trace Code for downloadable batch certificate- Batch certificate available to download from www.scilabware.com- Made in Great BritainPyrex Wide-Neck Erlenmeyer Flask 500mlVolume: 500 mlDiameter: 105 mm (at the base)Height: 175 mmOpeing inner diameter: 46 mm

€17
Volume discount! €16 per piece when you buy 2 or more
Pyrex Erlenmeyer Flask 1000ml

Pyrex Erlenmeyer Flask 1000ml

Original Pyrex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Pyrex Borosilicate glass. Idal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.- Complies with DIN ISO 24450- Erlenmeyer pattern- Manufactured from Pyrex borosilicate glass- Excellent thermal performance- High resistance to chemical attack- White enamel graduations and marking spot- Graduated to capacity- Printed with Trace Code for downloadable batch certificate- Batch certificate available to download from www.scilabware.com- Made in Great BritainPyrex Wide-Neck Erlenmeyer Flask 1000mlVolume: 1000 mlDiameter: 131 mm (at the base)Height: 220 mmOpeing inner diameter: 43 mm

€33
Pyrex Erlenmeyer Flask 2000ml

Pyrex Erlenmeyer Flask 2000ml

Original Pyrex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Pyrex Borosilicate glass. Idal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.- Complies with DIN ISO 24450- Erlenmeyer pattern- Manufactured from Pyrex borosilicate glass- Excellent thermal performance- High resistance to chemical attack- White enamel graduations and marking spot- Graduated to capacity- Printed with Trace Code for downloadable batch certificate- Batch certificate available to download from www.scilabware.com- Made in Great BritainPyrex Narrow-Neck Erlenmeyer Flask 2000mlVolume: 2000 mlDiameter: 153 mm (at the base)Height: 272 mmOpening inner diameter: 43 mm

€47
Pyrex Erlenmeyer Flask 3000ml

Pyrex Erlenmeyer Flask 3000ml

Original Pyrex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Pyrex Borosilicate glass. Idal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.- Complies with DIN ISO 24450- Erlenmeyer pattern- Manufactured from Pyrex borosilicate glass- Excellent thermal performance- High resistance to chemical attack- White enamel graduations and marking spot- Graduated to capacity- Printed with Trace Code for downloadable batch certificate- Batch certificate available to download from www.scilabware.com- Made in Great BritainPyrex Wide-Neck Erlenmeyer Flask 3000mlVolume: 3000 mlDiameter: 187 mm (at the base)Height: 310 mmOpening inner diameter: 43 mm

€103
Pyrex Erlenmeyer Flask 5000ml

Pyrex Erlenmeyer Flask 5000ml

Original Pyrex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Pyrex Borosilicate glass. Idal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.- Complies with DIN ISO 24450- Erlenmeyer pattern- Manufactured from Pyrex borosilicate glass- Excellent thermal performance- High resistance to chemical attack- White enamel graduations and marking spot- Graduated to capacity- Printed with Trace Code for downloadable batch certificate- Batch certificate available to download from www.scilabware.com- Made in Great BritainPyrex Erlenmeyer Flask 5000mlVolume: 5000 mlDiameter: 220 mm (at the base)Height: 365 mmOpening inner diameter: 43 mm

€131
Pyrex Media Bottle 250ml

Pyrex Media Bottle 250ml

Mix and store a wide range of culture mediums with these glass reagent bottles. Pyrex™ Borosilicate Glass Reagent Bottles with Polypropylene Cap and Pouring Ring feature a high chemical resistance and are designed with sloped shoulders for smooth pouring.- Bottles complete with polypropylene cap and drip-free pouring ring- Complies with ISO 4796- Printed with Trace Code for downloadable batch certificate- Sloping shoulders for smooth pouring action- White graduations and marking spot- Manufactured from temperature and chemically resistant borosilicate glass- For use up to 140°C- Made in Great BritainPyrex Media Bottle 250mlVolume: 250 mlDiameter: 78 mmHeight: 138 mmThread size: 45 mm

€19
Pyrex Media Bottle 500ml

Pyrex Media Bottle 500ml

Mix and store a wide range of culture mediums with these glass reagent bottles. Pyrex™ Borosilicate Glass Reagent Bottles with Polypropylene Cap and Pouring Ring feature a high chemical resistance and are designed with sloped shoulders for smooth pouring.- Bottles complete with polypropylene cap and drip-free pouring ring- Complies with ISO 4796- Printed with Trace Code for downloadable batch certificate- Sloping shoulders for smooth pouring action- White graduations and marking spot- Manufactured from temperature and chemically resistant borosilicate glass- For use up to 140°C- Made in Great BritainPyrex Media Bottle 500mlVolume: 500 mlDiameter: 86 mmHeight: 176 mmThread size: 45 mm

€24
Pyrex Media Bottle 1000ml

Pyrex Media Bottle 1000ml

Mix and store a wide range of culture mediums with these glass reagent bottles. Pyrex™ Borosilicate Glass Reagent Bottles with Polypropylene Cap and Pouring Ring feature a high chemical resistance and are designed with sloped shoulders for smooth pouring.- Bottles complete with polypropylene cap and drip-free pouring ring- Complies with ISO 4796- Printed with Trace Code for downloadable batch certificate- Sloping shoulders for smooth pouring action- White graduations and marking spot- Manufactured from temperature and chemically resistant borosilicate glass- For use up to 140°C- Made in Great BritainPyrex Media Bottle 1000mlVolume: 1000 mlDiameter: 101 mmHeight: 225 mmThread size: 45 mm

€33
Pyrex Media Bottle 2000ml

Pyrex Media Bottle 2000ml

Mix and store a wide range of culture mediums with these glass reagent bottles. Pyrex™ Borosilicate Glass Reagent Bottles with Polypropylene Cap and Pouring Ring feature a high chemical resistance and are designed with sloped shoulders for smooth pouring.- Bottles complete with polypropylene cap and drip-free pouring ring- Complies with ISO 4796- Printed with Trace Code for downloadable batch certificate- Sloping shoulders for smooth pouring action- White graduations and marking spot- Manufactured from temperature and chemically resistant borosilicate glass- For use up to 140°C- Made in Great BritainPyrex Media Bottle 2000mlVolume: 2000 mlDiameter: 136 mmHeight: 260 mmThread size: 45 mm

€56
Temporarily out of stock
View product
Pyrex Griffin Beaker 250ml

Pyrex Griffin Beaker 250ml

The standard low form beaker with spout was originally devised by John Joseph Griffin, an English chemist, in the nineteenth century. This laboratory icon has gone on to become one of the most widely used items of laboratory glassware.- Complies with ISO 3819 and DIN 12331- Manufactured from Pyrex borosilicate glass- Excellent thermal performance- High resistance to chemical attack- Printed with Trace Code for downloadable batch certificate- Batch certificate available to download from www.scilabware.com- White graduations and marking spot- Made in Great BritainPyrex Griffin Beaker 250mlVolume: 250 mlDiameter: 70 mmHeight: 95 mm

€17
Pyrex Griffin Beaker 400ml

Pyrex Griffin Beaker 400ml

The standard low form beaker with spout was originally devised by John Joseph Griffin, an English chemist, in the nineteenth century. This laboratory icon has gone on to become one of the most widely used items of laboratory glassware.- Complies with ISO 3819 and DIN 12331- Manufactured from Pyrex borosilicate glass- Excellent thermal performance- High resistance to chemical attack- Printed with Trace Code for downloadable batch certificate- Batch certificate available to download from www.scilabware.com- White graduations and marking spot- Made in Great BritainPyrex Griffin Beaker 400mlVolume: 400 mlDiameter: 80 mmHeight: 110 mm

€21
Pyrex Griffin Beaker 600ml

Pyrex Griffin Beaker 600ml

The standard low form beaker with spout was originally devised by John Joseph Griffin, an English chemist, in the nineteenth century. This laboratory icon has gone on to become one of the most widely used items of laboratory glassware.- Complies with ISO 3819 and DIN 12331- Manufactured from Pyrex borosilicate glass- Excellent thermal performance- High resistance to chemical attack- Printed with Trace Code for downloadable batch certificate- Batch certificate available to download from www.scilabware.com- White graduations and marking spot- Made in Great BritainPyrex Griffin Beaker 600mlVolume: 600 mlDiameter: 90 mmHeight: 125 mm

€26
Bomex Erlenmeyer Flask 1000ml

Bomex Erlenmeyer Flask 1000ml

Bomex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Borosilicate glass. Ideal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.Bomex Wide-Neck Erlenmeyer Flask 1000mlVolume: 1000 ml.Height: 215 mm.Diameter bottom: 135 mm.Diameter neck (inside): ca 43 mm.

€8,3
Temporarily out of stock
View product
Bomex Erlenmeyer Flask 100ml

Bomex Erlenmeyer Flask 100ml

Bomex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Borosilicate glass. Ideal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.Bomex Wide-Neck Erlenmeyer Flask 100mlVolume: 100 ml.Height: 110 mm.Diameter bottom: 70 mm.Diameter neck (inside): ca 29 mm.

€2,1
Temporarily out of stock
View product
Bomex Erlenmeyer Flask 250ml

Bomex Erlenmeyer Flask 250ml

Bomex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Borosilicate glass. Ideal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.Bomex Wide-Neck Erlenmeyer Flask 250mlVolume: 250 ml.Height: 140 mm.Diameter bottom: 85 mm.Diameter neck (inside): ca 31 mm.

€2,7
Temporarily out of stock
View product
Bomex Erlenmeyer Flask 500ml

Bomex Erlenmeyer Flask 500ml

Bomex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Borosilicate glass. Ideal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.Bomex Wide-Neck Erlenmeyer Flask 500mlVolume: 500 ml.Height: 185 mm.Diameter bottom: 105 mm.Diameter neck (inside): ca 34 mm.

€4,6
Temporarily out of stock
View product
Bomex Erlenmeyer Flask 2000ml

Bomex Erlenmeyer Flask 2000ml

Bomex Erlenmeyer flask with wide mouth and excellent thermal and chemical performance thanks to the Borosilicate glass. Ideal for yeast starters. Boil the wort, or malt extract and water, in the flask on a stove/hot plate. Cool in water bath and then add yeast. Close them flask mouth with aluminum foil or fermenter airlock.Bomex Wide-Neck Erlenmeyer Flask 2000mlVolume: 2000 ml.Height: 285 mm.Diameter bottom: 170 mm.Diameter neck (inside): ca 41 mm.

€19
Temporarily out of stock
View product
Glass Beaker Borosilicate Low 250ml

Glass Beaker Borosilicate Low 250ml

Low Glass Beaker - The standard low form beaker with spout was originally devised by John Joseph Griffin, an English chemist, in the nineteenth century. This laboratory icon has gone on to become one of the most widely used items of laboratory glassware.Glass Beaker Borosilicate Low 250mlVolume: 250 mlHeight: 10 cm.Bottom diameter: 7 cm.

€2,7
Temporarily out of stock
View product
Glass Beaker Borosilicate Low 100ml

Glass Beaker Borosilicate Low 100ml

Low Beaker made from Borosilicate glass with high heat- and chemical resistance. The standard low form beaker with spout was originally devised by John Joseph Griffin, an English chemist, in the nineteenth century. This laboratory icon has gone on to become one of the most widely used items of laboratory glassware.Glass Beaker Borosilicate Low 100mlVolume: 100mlHeight: 7,5 cm.Bottom diameter: 5,4 cm.

€2,1
Temporarily out of stock
View product
Glass Beaker Borosilicate Low 400ml

Glass Beaker Borosilicate Low 400ml

Low Beaker made from Borosilicate glass with high heat- and chemical resistance. The standard low form beaker with spout was originally devised by John Joseph Griffin, an English chemist, in the nineteenth century. This laboratory icon has gone on to become one of the most widely used items of laboratory glassware.Glass Beaker Borosilicate Low 400mlVolume: 400mlHeight: 12 cm.Bottom diameter: 8 cm.

€3,6
Temporarily out of stock
View product
Glass Beaker Borosilicate Low 600ml

Glass Beaker Borosilicate Low 600ml

Low Beaker made from Borosilicate glass with high heat- and chemical resistance. The standard low form beaker with spout was originally devised by John Joseph Griffin, an English chemist, in the nineteenth century. This laboratory icon has gone on to become one of the most widely used items of laboratory glassware.Glass Beaker Borosilicate Low 600mlVolume: 600mlHeight: 13,5 cm.Bottom diameter: 9 cm.

€4,6
Temporarily out of stock
View product
Glass Beaker Borosilicate Low 1000ml

Glass Beaker Borosilicate Low 1000ml

Low Beaker made from Borosilicate glass with high heat- and chemical resistance. The standard low form beaker with spout was originally devised by John Joseph Griffin, an English chemist, in the nineteenth century. This laboratory icon has gone on to become one of the most widely used items of laboratory glassware.Glass Beaker Borosilicate Low 1000mlVolume: 1000mlHeight: 15,5 cm.Bottom diameter: 11 cm.

€6,4
Temporarily out of stock
View product
Glass Beaker Borosilicate Low 2000ml

Glass Beaker Borosilicate Low 2000ml

Low Beaker made from Borosilicate glass with high heat- and chemical resistance. The standard low form beaker with spout was originally devised by John Joseph Griffin, an English chemist, in the nineteenth century. This laboratory icon has gone on to become one of the most widely used items of laboratory glassware.Glass Beaker Borosilicate Low 2000mlVolume: 2000mlHeight: 20 cm.Bottom diameter: 13,5 cm.

€14
Temporarily out of stock
View product
Pyrex Griffin Beaker 800ml

Pyrex Griffin Beaker 800ml

The standard low form beaker with spout was originally devised by John Joseph Griffin, an English chemist, in the nineteenth century. This laboratory icon has gone on to become one of the most widely used items of laboratory glassware.- Complies with ISO 3819 and DIN 12331- Manufactured from Pyrex borosilicate glass- Excellent thermal performance- High resistance to chemical attack- Printed with Trace Code for downloadable batch certificate- Batch certificate available to download from www.scilabware.com- White graduations and marking spot- Made in Great BritainPyrex Griffin Beaker 800mlVolume: 800mlDiameter: 100 mmHeight: 135 mm

€24
Stir Bar 12x3mm PFTE

Stir Bar 12x3mm PFTE

Teflon Coated (PTFE) stirr bar magnet without ring for magnetic stirrers. Dimensions: 12x3 mm.

€1,8
Stir Bar 27x8mm PFTE

Stir Bar 27x8mm PFTE

Teflon Coated (PTFE) powerful stirr bar magnet with ring for magnetic stirrers. Dimensions: 27x8 mm.

€2,7
Stir Bar 45x8mm PFTE

Stir Bar 45x8mm PFTE

Teflon Coated (PTFE) powerful stirr bar magnet with ring for magnetic stirrers. Dimensions: 45x8 mm.

€3,6
Magnet Pickup Rod 345mm

Magnet Pickup Rod 345mm

Teflon-coated rod for easy pickup of stirr magnets. Strong magnet, withstands heat, cold and has very high chemical resistance. Magnetic stirrer, stirrer magnets and beakers are ordered separately.Material: Teflon-coated (PTFE) metal with strong magnet.Dimensions: Length 345 mm, diameter 10 mm.

€13
Brewtools HopDrop Kit 4"

Brewtools HopDrop Kit 4"

Brewtools HopDrop Kit 4" for dryhopping and adding other ingredients to a pressurized fermenter without oxygen. Fits F100/F150/F200/F300 and other 4".Included in the box:- Butterfly-valve, TC 4"- TC Adapter, 4" til 34mm- TC Pipe, 4", L=200mm - Tri Clamp, 4" (2 pcs)- Tri Clamp, 34mm (3 pcs)- TC34mm Manual PRV- TC34mm Ball Lock connector, Gas- TC Tee, 34mm, L=60mm- TC Gasket, 4", (3 pcs)- TC Gasket, 34mm DN20, 5-pack

€373
Brewtools HopDrop Kit 3"

Brewtools HopDrop Kit 3"

Brewtools HopDrop Kit 3" for dryhopping and adding other ingredients to a pressurized fermenter without oxygen. Fits F40/F80 and other 3".Included in the box:- Butterfly-valve, TC 3"- TC Adapter, 3" to 34mm- TC Pipe, 3", L=200mm - Tri Clamp, 3" (2 pcs)- Tri Clamp, 34mm (3 pcs)- TC34mm Manual PRV- TC34mm Ball Lock connector, Gas- TC Tee, 34mm, L=60mm- TC Gasket, 3", (3 pcs)- TC Gasket, 34mm DN20, 5-pack

€345
Grainfather Seals for Conical Dual Valve Tap

Grainfather Seals for Conical Dual Valve Tap

Seals for Conical Dual Valve Tap O-rings are a complete set of replacement O-rings for Dual Valve Tap on Grainfather Conical Fermenter.Spare Part.

€8,3
Brewtools MiniUni 20L

Brewtools MiniUni 20L

Brewtools MiniUni 20L The MiniUni™ tanks are a series of high quality flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as water heating, storage of cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EU Specification:Pack size: 34 (w) x 34(d) x 61 (h) cmWeight without emaballage: 8 KgWeight with packaging: 9.3 KgTank diameter (inside): Ø28 cmMax. recommended volume: 20 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSI< strong>This comes with: MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-piece with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

€346
Brewtools MiniUni 30L

Brewtools MiniUni 30L

Brewtools MiniUni 30LThe MiniUni™ tanks are a range of high quality flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as water heating, storage of cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EUSpecification:Pack size: 34 (w) x 34(d) x 77 (h) cmWeight without emaballage: 9.65 kgWeight with packaging: 11.2 kgTank diameter (inside): Ø28 cmMax. recommended volume: 30 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSIThis comes with: MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-piece with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

€384
Brewtools MiniUni 40L

Brewtools MiniUni 40L

Brewtools MiniUni 40L The MiniUni™ tanks are a range of high quality, flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as water heating, storage of cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EUSpecification:Pack size: 34 (w) x 34(d) x 92 (h) cmWeight without packaging: 11.2 kgWeight with packaging: 12 kgTank diameter (inside): Ø28 cmMax. recommended volume: 40 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSI< strong>This comes with:MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-piece with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

€440
Brewtools MiniUni 50L

Brewtools MiniUni 50L

Brewtools MiniUni 50L The MiniUni™ tanks are a range of high quality, flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as water heating, storage of cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EU Specification:Pack size: 34 (w) x 34(d) x 108.5 ( h) cmWeight without packaging: 12.85 KgWeight with packaging: 14.8 KgTank diameter (inside): Ø28 cmMax. recommended volume: 10 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSIThis comes with: MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-piece with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

€477